Question about Bosch Nexxt Premium WFMC6400UC Front Load Washer

1 Answer

E02 Code E02 message, replaced water lines, filter clear. Now has plenty of water and pressure however still getting E02 message. E02 Message contined after problem fixed. Called Bosch, advised to have a "factory trained tech" come out to reset. I'll be really upset if I have to pay $99 (for the 1st 18 min) to have a tech push the start & ?? buttons or unplug machine for a few minutes to reset. How can I reset these codes? Thanks DW

Posted by on

  • tudobempa Nov 16, 2008

    Have been getting same code for the last couple of weeks. I push the start button again and it restarts; however, evidently there's a problem. Is the solution within the DIY domain? Thanks

  • tudobempa Nov 16, 2008

    What is an eprom? and where can I locate it? By the same token, where is the heating element located, and how could I test it? Hope these questions aren't too onerous to answer, thank you in advance, any help is immensely appreciated.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Faulty heating element, or main eprom is faulty

Posted on Jul 12, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I delete E02?


Depends on the make and model but an Error code E02 on most washing machines is slow water flow probably caused by a blocked filter! Remove panel on front bottom left or right side and clean filter! Should then clear error itself!

Oct 21, 2014 | Washing Machines

1 Answer

Error code F01 E02


For how long did you unplug the power cord? If it was under 5 minutes, unplug it for longer. Check if that clears the error code. If it doesn't, the motor control unit needs to be replaced.

Please double check your model number to get the correct part. Most of the Whirlpool washers have model numbers that start with 3 letters.

I hope this helps.

Cindy Wells

Dec 20, 2013 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have an E02 message and was just wondering if there are any adjustments that I can make. I have already turned the gas off and back on and checked the filters.


The E02 message says there is a high temperature condition. There are two sensors that detect this condition and a number of things can cause it. If the combustion gas or water flow is not high enough it could happen. One or both sensors could be bad. The flow regulator could be defective, etc. . I recommend you call the Pentair technicalsupport at 800-693-0971 and they should be able to help you figure this issueout. I hope this helps.

Please vote on this answer. Thank you.

Aug 27, 2011 | Pentair Pool & Spa

1 Answer

I have a problem with my kenmore elite which is made by lg. the water on the despencer will stop producing water. i have to take filter out and shake water out and then i put it back. about l hour later it...


If you have changed the filters, check and make sure the line is clear coming from water supply, and you have plenty of pressure from the valve that feeds the water dis, usually it lies in the water pressure, the valve or the filters

Feb 06, 2010 | GE GSH25JFR Side by Side Refrigerator

1 Answer

Samsung washing machine gives Low Water pressure error message and interrupts cycle. Checked inlet filters. Sometimes gives leak/flood warning message. How can I turn off these messages?


You get these messages turned off by fixing the problem.

Low water pressure is basically one of the valves is not letting water pass through.

1. Do as you already did and clean the inlet filters. Any kinked hoses?

2. Adjust the water pressure in the house. Is it too high or too low?

3. Replace the valves in the unit.

4. Main board.

Dec 29, 2009 | Samsung WF448AAP Front Load Washer

2 Answers

We have a jenn-air jfc2087hrs (french door model) and the water pressure from the internal water dispenser is very low. the line has plenty of pressure.


If your ice maker is making full size cubes then it should one of 2 problems.
The water valve on the bottom back of the machine is a dual valve. One side feeds the ice maker, the other side feeds the water supply.
1. The dual water valve. is going bad. The water side is malfunctioning.
The dual valve must be replaced.
2. Your model should have filters for the water dispenser, and need replaced.
Try changing the filters first.

Oct 04, 2009 | Jenn-Air JFC2087HRS Side by Side...

1 Answer

I get a check water tap error 2 to 4 times a load


I have this problem. This code is due to restriction of water flow. In my case, we have sand in our water, and I have installed a filter between the water line and the washer. When it gets clogged, the flow is restricted and the Check Water Tap message appears. Your washer has filters on the back of the washer itself that may be clogged and need cleaning (which is why I installed the water filter between the washer & water line to prevent it from getting into the washer filter). Your washer manual shows you how to check/clean them. Also, you may have low water pressure during summer months due to lawn watering in your area that could cause this lower water pressure.

Jun 23, 2009 | Bosch Nexxt Premium WFMC6400UC Front Load...

1 Answer

I keep getting the E02 message in safeguard mode, what can I do?


I keep getting the E02 message in safeguard mode, what can I do?

Dec 25, 2008 | RCA CC6263 Camcorder

1 Answer

E02 message


Error relates to water taking to long to get into machine. Check tap is open fully, water pressure is ok, hoses are not kinked. also check the small filters either end of the inlet hoses (inlet valves as well) as quite often they can clog up especialy on a new install. Regards

Jul 22, 2007 | Bosch WFMC 3200 Front Load Washer

Not finding what you are looking for?
Bosch Nexxt Premium WFMC6400UC Front Load Washer Logo

3,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

jimorris77

Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...