Question about Network Accessories

2 Answers

How to operate 2 tv using one set top box with two differt remote contr

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 565 Answers

Coax out on ctv box to coax splitter. coax to each tv from splitter. u will have the same channel on both tv's...otherwise pay for another cable box.

Posted on Jan 27, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How two tv connect with airtel stb i tried with splitter but no result on second tv plz suggest some thing so i able to watch on second tv

Posted on Jun 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vextra remote codes for toshiba tv


How to auto program this remote
1. Turn on the device to be programmed.
2. Press and hold SET for three seconds
3 Press the corresponding Device Button (TV, SAT, VCR, DVD,CBL,Audio)
4. Aim the remote at the device. Press the power button once and release. Each time the Remote searches for a code, the device button LED flashes twice. When the device turns off, immediately press ENTER to save the code (before the device button LED flashes again) This could take several minutes.

Aug 21, 2013 | Network Accessories

1 Answer

3250hd


How have you connected the audio cables to the TV? The 3250HD has component, DVI, and composite video out. There is also two analog audio outputs (for the component and composite video) and a digital audio output. Make sure that you are using a TV and not a monitor. Many monitors do not have built-in speakers. (In that case, use external speakers.)

If you use the digital audio output, make sure that your audio receiver audio input is connected to the set top box audio out. Then make sure to set the correct source for that audio signal. (Note the TV may have a digital audio port; that is an audio out.)

If you are using one of the analog audio outputs directly to the TV, make sure that you are using the correct set of audio IN on the TV and audio out on the set top box. (If you are on the Component input, your audio won't be heard if you are using the Composite audio output.)

Next try different audio cables. Make sure that the TV speakers are on. (Some TVs have an option to disable the speakers if you use external speakers at times.) Try connecting the audio output to a receiver and speaker system (or speakers with aux in). You might need an RCA F/F to 3.5 mm M adapter for some devices. If another set of speakers do not work, then the set-top box probably has a broken audio output. If another set of speakers work, then the problem is with the TV audio. This could be a problem with the jack or the speakers.

I hope this helps.

Cindy Wells

May 02, 2013 | Black Box Network Accessories

1 Answer

I wanted to set 2 tv from one box , is there any device which can convert digital signal in to analog


standard digital to analog TV tuner will do this you just need to add a RF splitter on the output.

Mar 19, 2013 | Network Accessories

1 Answer

The scrren either says resolution is not supported (mode 1) or the screen wiggles and shakes (mode 2). A directly connected pc works fine. I am sending to a tv with pc input as the remote display


The QVS VBC5 video extender supports a maximum resolution of 1600x1200 @ 60Hz for up to 50meters (164feet) & 1024x768 @ 60Hz for up to 100meters (330feet).

Make sure your maximum distance of Category 5 cable from your source to your television is no longer than 330 feet if using a 1024x768 resolution. Try dropping the resolution on your source computer in Mode 2 to resolve the issue.

Mar 29, 2011 | QVS VBC5 VGA/RGB Video CAT5e Extender ...

1 Answer

Dvr restart


WARNING: this will wipe out all of your recordings, all scheduled recordings, all series recordings (your series priority list), and all manual recordings!! Write down everything you can before you do this!
  1. The DVR should be turned on. Press CABLE, POWER to turn off the box.
  2. Immediately press OK/SELECT to bring up the diagnostics page.
  3. While on this screen, press the following key sequences press the counter-clockwise arrow (REPLAY on some remotes) 2 times, then press the MyDVR (LIST on some remotes), button 3 times then the live button 2 times."Clr" will appear on the LED display.
  4. Press OK/SELECT to proceed with the reset. The STB should now reformat the HD & then perform a STB reset and begin to reload your Cable settings and Time Settings from the Head End. It will then begin to populate the Guide data over the next 2 - 24 hours.
On some systems, the button press pattern may be 1-3-1, not 2-3-2 as above. This is true for at least the DCT 3416 I on Shaw.

Feb 17, 2011 | Network Accessories

1 Answer

I have two tv in different room but cable line is one with set top box .Now I want to connect the both tv.


You should try to find active splitter 1 IN 2-3 OUT connections. If cable is not too long it should work. So connect line into IN port nad two TV cables into OUT ports. This is the easiest and cheapest solution. Maybe you will need to mount proper connectors on the cables. Good luck!

Nov 17, 2010 | Sony Network Accessories

1 Answer

Change default channel on cable box


Called the cable provider, Time Warner, and used the "settings" menu to navigate to power on channel, where I selected the default channel.

Nov 13, 2009 | Atlantic Scientific Network connector

1 Answer

WIRING NEEDED TO HOOK LAPTOP TO TV FOR PPS PRESENTATION


well you need to use the VGA TO VGA Cable and some toshiba laps needs to set it on that mode by pressing Fn+F10.

May 31, 2009 | Network Accessories

1 Answer

Black-box regd


There are NO drivers needed or even provided by BlackBox for this device. It simply uses hardware circuits to convert an RS232 signal to a RS 422/485 signal. My first reaction to this question is: Do you have your PC serial port at 9600baud which is the default RS232 signalling rate for this device? (I guess I probably won't hear a response on this as the question is almost a year old, with no attempts by anyone to solve it. I'm the only glutton for punishment.) ZT3000 "Beta tester of "0"s and "1's"

Sep 28, 2006 | Black Box Serial Adapter

Not finding what you are looking for?
Network Accessories Logo

Related Topics:

4,924 people viewed this question

Ask a Question

Usually answered in minutes!

Top Network Accessories Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Cindy Wells

Level 3 Expert

4757 Answers

Are you a Network Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...