Question about Viper Televison & Video
I bought a new 7652v remote and I would like to add it to my current alarm. How do I program it? I have one, that came with my alarm but I want to add one more one way remote.
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Whoever hooked up your system did not hook up the factory alarm disarm and arm wires. Your car thinks it is being stolen as a result of this. You need to get a wire diagram of your car and hook up the proper wires.
Posted on Dec 04, 2008
this usually means that the remote did not recieve a signal back from the module or the module did not recieve the remote signal
have you tried repeatively to press the unlock button? does the remote starter work or aux( trunk ) ?
also when putting the battery in the remote , be easy because there is a connector plug soldered on the board real close to where the battery is , and if it is hit by the battery hard enough it will cause those solder connections to disconnect and you will get the beeps and or other malfunctions
Posted on Feb 03, 2009
SOURCE: Viper 5701 remote programming
1st you need to enter the remote into progamming Hold the Function button until the remote gives a long beep and LED light comes on the remote a (it takes about 8 sec.) Then press and hold the remote start buttom until the remote beeps 3 times and LED lights up. Now your ready to program the remote
One of the door has to be open . Insert the key - turn the key to the On position then press the button on the antenna once and then press it again and hold it
You hear a chirp and then you press the lock button on the remote and then you hear a second chirp to recieve confirmation and then release the button and the turn off the key .
Remote should be program
Posted on Jul 12, 2009
first you will need to locate your valet switch/button, which will be a black push button located somewhere under the driver side dash.
Open a Door,
Turn your key to ON position,
within 5 seconds of turning your key to the ON spot,
press and release the program button 1 time, then press it a 2nd time and hold it this time
the L.E.D will flash one time and then you will hear a chirp,
while still holding the valet switch, press the lock button on your new remote. you should hear a single chirp.
After chirp you can release the program button and turn the key to off.
you should hear a long chirp when the alarm exits the programming
try the remote
if the remote functions don't work properly, you can always try a different # pattern.
ex: press 2 times and hold on the 3rd, press 3 times and hold on the 4th.
Posted on Aug 18, 2009
If you go to the website then to the support page under guides, you can find your models manual which give you installation and reprogramming instructions.
Posted on Oct 26, 2009
Tips for a great answer:
Jul 01, 2016 | 1998 Toyota Corolla
Jan 05, 2016 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START
Feb 17, 2015 | Viper Vehicle Parts & Accessories
Dec 12, 2014 | Viper Vehicle Parts & Accessories
Apr 02, 2014 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START
May 16, 2013 | Emerson New Original VCR4010A Remote...
Jan 19, 2013 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START
Jul 02, 2012 | 2000 Pontiac Grand Prix
Jun 13, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START
Oct 18, 2010 | 2001 Harley Davidson FLSTC - FLSTCI...
221 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: