Question about Proform Exercise & Fitness

1 Answer

Proform 560 crosstrainer treadmill powers on belt won't turn

Console powers on but when start is pressed nothing happens. Incline works. Console operates as is working.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Proform Master
  • 12,223 Answers

LUBE THE deck belt+ rollers bearing too. God bless you
proceed according with the video attached.

Posted on Jan 07, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: Proform 515s treadmill motor won't start

If the colse buttons make a chirping noise when you push them the console should be Ok. If there is no chirping noise with the push it is a bad console. If everything but the speed works it will probably be your motor controller that is bad.

Posted on Apr 14, 2009

  • 1 Answer

SOURCE: proform xp 680 crosstrainer treadmill keeps

Mine did the same thing. I ran it to a dedicated non GFSI circuit and the problem was eliminated

Posted on Nov 29, 2009

  • 1 Answer

SOURCE: The belt on my ProForm Crosstrainer treadmill stops while using i

Sometimes the tread needs to be lubricated. This was the case with ours. You can get a lubrication kit at ****'s Sporting Goods or other larger sport stores and it will instruct you on how to do it.

Posted on Jan 26, 2010

  • 1 Answer

SOURCE: I have a proform j8li treadmill, all 4 led lights

I have the exact same problem with the very same treadmill that i bouth 10 years ago and it has been sitting for 5 years unused. The last time it was turned on it worked but now that I plug it in and try to start it, everything works but the belt drive motor. Any ideas?

Posted on Feb 09, 2010

maxtreadmill
  • 832 Answers

SOURCE: Proform Crosstrainer 5.0 Treadmill

ICON CALIBRATION INSTRUCTIONS- INCLINE
1) Press the Stop and the Speed Up keys down while inserting the safety key. If this doesn’t work, click on the help topic entitled “Alternate Calibration Codes” for key sequence instructions to enter calibration.
2) Press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test.
3) Press either incline key and the incline will calibrate automatically.
4) THIS IS A VERY IMPORTANT STEP BECAUSE YOU WILL GET AN ERROR MESSAGE IF THIS STEP IS SKIPPED.After completing calibration of incline, press the Stop key and then remove the safety key.

Posted on Jul 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hallo, I have a problem with my PROFORM 760 AIR, and when it takes 3 or 4 minutes. for themselves, or when X passes also for speed.


tes the speed sensor. RUN the software calibration for troubleshooting and fix it. God bless you
755de5d2-2307-4164-9313-a5be55a48396.gifVersion:1.0 StartHTML:0000000168 EndHTML:0000003648 StartFragment:0000000468 EndFragment:0000003631

The Steps for Newer Style Console Calibration

  1. Locate the calibration area on the rear or underside of the console (a hole, near the console's center, that goes through to the electronics board. (This hole should not have a screw in it.)

  2. Insert a pencil (eraser end), into the hole and feel around for the cal button (will click when pressed).

  3. Press the button 2 times (with the pencil eraser). The first click should show CL11 in the console, the second click should show CL21.

  4. If the process was done correctly, and CL21 appears in the console, you are in "calibration mode." The next few steps consists of pressing buttons on the console and observing settings. This will not require any other tools.

  5. Press ENTER. CL22 should display in the TIME window and (??) in the SPEED window.

  6. Press ENTER. CL23 should display in the TIME window and (??) in the SPEED window.

  7. Press ENTER. CL24 should display in the TIME window and (??) in the SPEED window.

  8. Press ENTER. CL25 should display in the TIME window and (??) in the SPEED window.

  9. Press ENTER. CL26 should display in the TIME window. You should then see the letter "E."

  10. Press ENTER. You should see "SS" or "55" in the console.

  11. Push the STOP/START button. For safety, at this point, you should step off, or be off, the treadmill.

  12. Push the ENTER button. The walking belt should start to move, accelerate to maximum speed, then stop on its own.

  13. When the belt stops, the incline should self test by raising to its highest incline position, then lowering back down to its lowest position.

  14. Once the incline test is complete, push the POWER button 2 times. The unit should shut off and the console should go completely blank. If this happens, the treadmill is done calibrating and is ready for use.

  15. If the letter "F" appears in the SPEED or INCLINE window when the power button is pressed 2 times, the treadmill is indicating a failure somewhere either in the SPEED or INCLINE (depending on the window the "F" appeared in). Troubleshooting the failure would be the next step.

Apr 04, 2013 | Proform 760 CrossTrainer Treadmill

1 Answer

Proform 560 HR , lights up but walking belt wont move , can it be fixed ? Help please :) thanks in advance


Sounds like a lower motor controller, that would be the first part I'd replace. Be aware that treadmills have a high power draw and if you are also running other power suckers on the same circuit, the low voltage tends to short out the console or the control board.
The control board is easy to get to, and cheaper to replace than a console, but not cheap. You can also call the 800 number on the front of your owner's manual and they may help you diagnose it.

Jan 31, 2013 | Proform CrossTrainer Treadmill

1 Answer

Image 10.2i incline goes up and down when turned on


Please Run the software calibration for troubleshooting.
However you must test the relais , clean it, and test for open or faulty. see the diagram attached.
Lube the gear+shaft motor. Adjust the Potentiometer A LITTLE.
God bless you1_21_2013_4_22_29_pm.jpg1_21_2013_4_23_07_pm.jpg1_21_2013_4_23_37_pm.png

Jan 21, 2013 | Icon Proform 560 Crosstrainer Treadmill

1 Answer

Incline motor ran away, won't work after replacing


see the diagram attached and test test the input motor voltage, if there are the motor is faulty.see my personal TIPS.
God bless you

11_19_2012_3_43_18_pm.jpg11_19_2012_3_43_37_pm.gif

Nov 18, 2012 | Proform XP 580 Crosstrainer Treadmill...

1 Answer

Incline won't shut off


Please RUN The software calibration for diagnose, troubleshooting and fix it.
download your inst.manual from www.iconservice.com or www.fitness.manualsonline.com and proceed according

God bless you

Jul 18, 2012 | Icon Proform 560 Crosstrainer Treadmill

1 Answer

Proform Crosstrainer 5.0 Treadmill


ICON CALIBRATION INSTRUCTIONS- INCLINE
1) Press the Stop and the Speed Up keys down while inserting the safety key. If this doesn’t work, click on the help topic entitled “Alternate Calibration Codes” for key sequence instructions to enter calibration.
2) Press the Stop key one time. The Time window should read EP:2P. Some newer models may also say FP, Pass, or the like. This means that it passes the EPROM test.
3) Press either incline key and the incline will calibrate automatically.
4) THIS IS A VERY IMPORTANT STEP BECAUSE YOU WILL GET AN ERROR MESSAGE IF THIS STEP IS SKIPPED.After completing calibration of incline, press the Stop key and then remove the safety key.

Jul 15, 2010 | Proform Exercise & Fitness

1 Answer

Treadmill will not level out and motor sounds all the time


If the incline moves but only just a bit, it could be a problem as simple as the gearbox on the motor being jammed. We remove the motor from the treadmill, reconnect the wiring, and then try to run the incline motor outside the treadmill. Many times, this will unjam it if that is the problem and then reinstalling it in the treadmill will get it to work. If you have the same problem or it doesn’t run outside the machine and you can hear it try to work, you need to replace the incline motor.

Jun 27, 2010 | Proform 575 Crosstrainer Treadmill

2 Answers

Proform 740CS runs okay but the incline does not


ProForm Treadmills have a reset procedure for the incline function. With the key inserted in the console, activate the incline; while the incline is changing, remove the key. Wait 30 seconds, then replace the key. The incline should to maximum, then to minimum, resetting its limits. It worked for mine just 10 minutes ago; the procedure is in the manual if you have it. Good luck!

Mar 09, 2010 | Proform 7.0 Crosstrainer Treadmill

1 Answer

My treadmill proform835QT fails to incline. What can I do?


Try to calibrate the incline: Hold down the stop and speed up buttons at the same time then insert the key. release the buttons the press the stop button and release then press the incline up button. the incline motor should go all the way up then all the way down with - - on the console. If the unit only moves just a and inch or so or the motor just hums , the incline sensor is faulty.

Jan 15, 2010 | Proform CrossTrainer Treadmill

1 Answer

Proform 515s treadmill motor won't start


If the colse buttons make a chirping noise when you push them the console should be Ok. If there is no chirping noise with the push it is a bad console. If everything but the speed works it will probably be your motor controller that is bad.

Apr 14, 2009 | Proform CrossTrainer Treadmill

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

128 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...