Question about Volfenhag ZX-8300 Car Audio Amplifier

Open Question

Need to know how to wire my amp volfenhag zx-8300 1200 watt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Devsta
  • 68 Answers

SOURCE: need help please...

If you unplugged the fuses, the amp won't come on at all. I'd say its a blown transistor, you can test this by opening up the amp and using a multimeter to check resistance on the transistors.

Posted on Aug 05, 2009

raberd14
  • 60 Answers

SOURCE: i have a volfenhag zx-8400 amp

The voltage prolly says like 100Mv-2v, it doesn't really matter, just know that that the lower you turn it the harder it bangs. The X-over depends on where your box is tuned, crank the knob down too about 40htz and you'll prolly be good, just don't turn it lower than your box's tuned frequency. And your rca's go to line input. And there shouldn't be a problem with mounting your amp vertically, you prolly just had a bad connection. Hope this helps if you have more questions please ask...

Posted on Sep 21, 2009

HitWizard
  • 67 Answers

SOURCE: volfenhag amp adjustments

Firstly, you will want to set all options to a low pass, so the high frequencies are filtered away from the subs, avoiding damaging the voice coil. Start with the Gain of the amp about 3/4 of the way up, and all other knobs, such as the bass knob to the lowest setting. From there, test your subs for soujnd, and then change the gain and amount of bass for the sound you desire, since each person is different. I have my gain about 1/2 way up and the bass about 1/4 of the way up. If you have a crossover knob, set it to the highest frequency available, since the low pass will filter all the high frequencies out anyway.

Posted on Sep 24, 2009

mbostermeyer
  • 58 Answers

SOURCE: I have a volfenhag zx-8400 and it just geos into protection mode

The most likely problem would be a blown fuse. I would replace all of the fuses.

Posted on Oct 24, 2009

  • 1 Answer

SOURCE: i just bought a volfenhag zx-8200 amp yesterday

ckeck your + s and - s, otherwise it could an interal problem in the amp

Posted on Jan 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size of fuse do I use


easy divide volts into watts and this will give you the amperage so a 12v x200 watt amp needs a 20 amp fuse

May 27, 2011 | Volfenhag ZX-7180 Car Audio Amplifier

1 Answer

Need help setting amp right


volfenhag's are cheap. you get what you pay for. that is the german equiv. to pyramid or kraco.

Jul 10, 2010 | Volfenhag ZX-5007 Car Audio Amplifier

1 Answer

Protect mode


Protection circuit.
Checek the wiring of the amp and speakers, don' forget to look for shorts at the speakers. Make sure no wires are touching each other

Apr 30, 2010 | Volfenhag 1600 WATT CHROME AMP AMPLIFIER 2...

1 Answer

I have a volfenhag zx-7170 amp with 2 chanels burnt out can i get this rebuilt to higher wattage specs and if so where can this be done


Anythings possible but would not justify the cost of the upgrade. What be cheaper to get a new one with more watts.. No one really upgrades amps as the cost of new ones are so affordable.

Nov 04, 2009 | Volfenhag ZX-7170 Car Audio Amplifier

1 Answer

I have a volfenhag zx-8400 amp. i dont have a manual. whats the proper way of conecting amp? its mounted on my speaker box, which is ported, 12' volfenhag 2500 watts. on the side of amp it had voltage...


The voltage prolly says like 100Mv-2v, it doesn't really matter, just know that that the lower you turn it the harder it bangs. The X-over depends on where your box is tuned, crank the knob down too about 40htz and you'll prolly be good, just don't turn it lower than your box's tuned frequency. And your rca's go to line input. And there shouldn't be a problem with mounting your amp vertically, you prolly just had a bad connection. Hope this helps if you have more questions please ask...

Sep 21, 2009 | Volfenhag ZX-8400 Car Audio Amplifier

1 Answer

I have two volfenhag 1000 watts speakers


If you are looking for some serious sound try using a Rockford Fosgate P3001T Amplifier.. it pushes 3000W Max its a 4 channel amplifier. Or you could go with something small. I have two JL Audio 10s in my car running with a 600W 2 Channel MTX Amp.

Apr 03, 2009 | Volfenhag ZX-4812 Car Subwoofer

1 Answer

How to wire a volfenhag dual coil sub


U HAVE TWO COILS ONE ONE EACH SIDE OF THE WOOFER, ALL U DO IS HOOK UP ONE COIL TO THE OTHER, THEM HOOK THEM UP TO THE TERMINALS IN THE BOX.

Oct 12, 2008 | Volfenhag ZX-4812 Car Subwoofer

Not finding what you are looking for?
Volfenhag ZX-8300 Car Audio Amplifier Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volfenhag Car Audio & Video Experts

Robert Rankin

Level 2 Expert

338 Answers

Professor_V
Professor_V

Level 2 Expert

92 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Volfenhag Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...