Question about Amana PTC093B35AE Air Conditioner

1 Answer

Amana PTAC ptc093d35ar, when i switch to remote t-stat i get a H1 code in the display. Can you help??? Joe

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 142 Answers

H1=High voltage protection engaged. Power supply voltage is too high. Check for incoming power at correct voltage.

Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find a troubleshooting manual for the DS01E amana t-sta?


http://www.amana-ptac.com/Portals/3/PTAC/PDF/DigiSmart%20DT%20DS%20DD%20Wireless%20EMS%20Installation%20Instructions%202010.pdf

Feb 19, 2015 | Amana DS01E - DigiStat Thermostat with...

1 Answer

My amana ptac is not heating....the code "np" is displayed....how do I correct this...we just installed the unit and know little about operation. Thanks


I don't see this error code in the manual. I do see nP as an error code for Window Switch lockout. I just had this happen to me and they had me reset the control board.

Remove case, flick master switch to OFF for 10 seconds. Press Heat/Cool same time turn switch back on HOLD until off light comes on.

You should be fixed. Just had to do this for my unit. I was playing around with the settings and turned on the window switch option by accident.

Feb 02, 2013 | Amana In Wall Install Kit For Digismart...

1 Answer

I have an Amana packed unit...blows cold air when on heat but if i turn temp to 90 then heat will come out but not at 72 or that range.


you probably have a packaged unit with a line voltage thermostat which is out of calibration...not an unusual situation. other than replace the stat, why not just use it by just setting where you need to - to get the results you desire? use a regular thermometer placed where you want to control to help you adjust properly.

Jan 27, 2013 | Amana R410a Package Terminal Ac Ptac 7600...

1 Answer

Installed Amana PTAC DigiSmart unit in a patio room, a entertainment bar is located about three feet (3) in front of unit and not the room. The unit only heat and cool the area between unit and the bar...


I have seen this happen many times and if you cannot relocate the bulb of the thermostat to keep it form short cycling, I have mounted a wall thermostat and disconnected the thermostat in the PTAC and wired it in to the wall stat. You may have to install a wall stat in the center of the room away from the bar.

May 15, 2011 | Heating & Cooling

1 Answer

I have thru-wall PTAC Amana PTH093B35AM unit. I


see if you can find a new board the power failure fried it

Jun 19, 2010 | Amana PTH093B35AM Thru-Wall/Window Air...

3 Answers

Looking for manuel reset on heater amana ptac unit heat won't come on new control board


I dont know about this model but in general electric heat wont have a reset button the heat is controled by a sequencer and each elememt has a safty limit switch incase the sequencer sticks in the on mode here is a link to where you can get more info on this model http://www.fixya.com/support/p51773-amana_ptc153b35aj_air_conditioner

Oct 30, 2009 | Amana PTC153B35AJ Air Conditioner

1 Answer

How do you override the FD in the Display of the Amana PTAC


I just had that problem of having fd display and it locks everything up. makes sure you check the ds1 and ds2 and ms1 and ms2 if these are shorted then you will get that problem. I had to wiggle the wires in the connector and it worked as soon as i pushed on the right wire. They apparently are very sensitive.

Jun 09, 2009 | Heating & Cooling

1 Answer

Remote Thermostat


call the amana dealer nearest to you order one

Jun 06, 2008 | Amana PTH123B25AJ Heat Pump Air...

Not finding what you are looking for?
Amana PTC093B35AE Air Conditioner Logo

Related Topics:

614 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Donni Steen

Level 3 Expert

659 Answers

Bill Long

Level 3 Expert

587 Answers

Are you an Amana Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...