Question about Dual Baofeng Uv-5r Band Uhf400-480mhz Vhf136-174mhz Radio 65-108mhz

1 Answer

Baofeng Uv-5r beeps on tx

Beeps when you try to TX

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Prodigy:

    An expert who has answered 500 questions.

  • Expert
  • 607 Answers

Hi Nick,

Your two way is giving you a roger beep, when you release the PTT, is that correct?

If so, your manual if you have one, and if you can decipher CHINGLISH, will tell you how to stop the ROGER BEEP.

Because these nasty little units are mass produced in China, their English translation of the user manual is harder to work with than the nasty little radios they are printed for.

Unless you have a mate who can translate Chinese to PROPER english for you, then you are in the same boat as the many other silly sausages that bought these crappy things.

They are cheap & nasty radios, like anything else made in China, that's not to say the Chinese people a bad, just the companies that produce this rubbish in great quantities for gullable folks to buy & cry.

Sorry, but I too got sucked in buying Chinese radios, Never again.

I hope you find someone to translate that Chinglish manual for you.

Sincere Best wishes,
Peter

Posted on Mar 05, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Samsung 32" keep beeping? no picture, beeps every 4 sec.s and the power lights flashes. Why???


The set is trying to start but it is detecting a problem so it keeps trying. Most likely you have a horizontal or high voltage problem. Hard to say. Have a shop check it out for you. Thanks

Oct 28, 2009 | Samsung TX-P3264 32" TV

1 Answer

Very low TX output power on ALL HF BANDS ONLY. Other bands OK!


look for a broken or cracked board near the driver s & finals, try pushing around on the board with your plastic screwdriver, you may luck into it.

Jun 09, 2009 | Radio Communications

1 Answer

I NEED TO KNOW HOW TO PROGRAM IT


It should be
  1. open door
  2. turn ignition on
  3. press and hold valet switch until it beeps once let go
  4. press once more and press lock on fob
  5. let go of buttons
  6. turn off ignition

May 29, 2009 | 473L TX 3-Button Replacement TX Remote

2 Answers

My viper alarm remote just beeps flashes TX and will not unlock doors or disarm my system. It has a new battery.


Try to reprogram this. If this routine does not work please let me know and we will try something else

May 06, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Low TX PWR/ATU won`t tune. No SWR and ALC metwr reading?


You've replaced the pre driver, the drivers and finals. Set bias and still low output. The pre driver is the same transistor used as the tx exciter transistor on other pcb chassis on bottom of radio. Follow the gray coaxial wire from the pre driver on the RF circuit board back to the tx/rx i.f. Circuit board. The gray coax cable plugs right next to the tx exciter transistor on this pcb. Again it's on a different pcb all together and on the bottom of the radio and also. Replace it! And check for open bias or emitter to ground chip resistor next to it. You will get your drive back. Very few rigs have I seen the actual Finals blown in the mosfet or the bipolar version. Just the driver stage with a week pre driver and the SMT "pre" pre driver on the same RF pcb. And the tx exciter on the other pcb.

Apr 24, 2009 | Computers & Internet

1 Answer

Tv only beeps


shorted power supply that beep is the power trying to come up

Dec 25, 2008 | Sony Grand WEGA KDF-60XBR950 60" Rear...

2 Answers

"line in use" lcd display


here is link
http://slayo.com/resetting-error-e27-waste-ink-absorber-full-canon-pixma-mp150mp160.html

you will need to do no3

EEPROM reset

Just follow instructions!
Checked by me and its working
Marko - SERBIA

Sep 11, 2008 | Canon FAX-JX200

1 Answer

Beeps and changed product description


Try reinstalling the Creative Mass Storage Driver 1.07.00.250 so that your computer properly recognizes your player again.

Once you have done that, try reinstalling the latest firmware update, Creative MuVo TX FM Firmware 1.24.02.

Apr 16, 2007 | Creative Labs Nomad MuVo TX MP3 Player

Not finding what you are looking for?
Dual Baofeng Uv-5r Band Uhf400-480mhz Vhf136-174mhz Radio 65-108mhz Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Radio Communications Experts

BJ Russell

Level 2 Expert

214 Answers

Brad Brown

Level 3 Expert

17328 Answers

Steve

Level 3 Expert

3289 Answers

Are you a Dual Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...