Question about Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

1 Answer

Too much play in upright part of my Hoover upright wind tunnel

Do I need to tighten the handle release lever. If so, how do I do that please?

Posted by on

  • HooverWindy Jan 20, 2009

    Thank you for the answer. I looked before asking and didn't see any damage underneath. I'll take it to the repair person before I make it worse. Thank you again for your help! : )

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 294 Answers

No. The handle release pedal is snapped into the bottom base assembly. Look underneath to check for cracks or damage in this area. this is the most likely issue. If it is, then the base will need to be repalced.

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hoover wind tunnel just quit while vacuuming. It is dead??? Two years old used about every other week? Any suggestions?


Some Wind Tunnels by Hoover have a poor design in the switch on the handle. Sometimes the switch does not turn on all the way and will stop running. Other times you can't turn the unit off.

Feb 28, 2015 | Hoover Self-Propelled WindTunnel Bagless...

2 Answers

Hoover Wind Tunnel Off-0n Switch


not sure about the part number.

but you can get it off by removing the four screws and the pulling it from opposite side

Jul 28, 2008 | Hoover U6437-900 / U6439-900 Windtunnel...

1 Answer

Hoover Wind Tunnel Bagless problem with carpet hight adjustment


Hi There Alec from VacuumSpot here.
Most of these machines don't actually change the height until the handle is lowered so even though you change the dial when it is an upright position it is not until you lower the handle that the height is actually selected. Assuming that you are aware of this and it is still not adjusting I would suspect you have a small arm or lever broken. It is very rare for a height selector to simply fall out of place.The job would take 5 minutes in my opinion so it is simple but a bit fiddly.

Dec 01, 2012 | Hoover U6630-900 WindTunnel Bagless...

1 Answer

My new Hoover Wind Tunnel Upright UH50000 will not turn off unless I unplug it.


First I would be sure the handle was properly installed. Remove the two screws holding the upper handle in place and tap it bacwards to remove it. Set the switch inside to the OFF position. Next set both buttons on the handle to the OFF position and re-install the upper handle. If the switch still does not turn the vacuum on and off, the switch will need replacement.

Apr 01, 2011 | Hoover U6630-900 WindTunnel Bagless...

1 Answer

How do you change the Hoover wind tunnel belts?


If you turn the vacuum over there will be (4) screws that hold on the base cover for the roller brush. Remove the screws and the cover and you can get to the belt(s). You can get replacement belts here:

Hoover Windtunnel Belts

Nov 18, 2009 | Hoover Company Wind Tunnel U53019 Upright...

4 Answers

Hoover Self Propelled wind tunnel vacuum U6433-900


please go to thehooverstore on the web. they'll have an exploded diagram of how your machine goes together. I'm sure you'll find your solution there.

Sep 02, 2007 | Hoover Ultra U6430-900 WindTunnel Bagged...

1 Answer

Problem with vacuum suction in upright position


Move the lever on the front of the machine to "carpet". It won't agitate on floor

Apr 11, 2007 | Hoover Company Wind Tunnel U53019 Upright...

Not finding what you are looking for?
Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18381 Answers

Roger Potts

Level 3 Expert

694 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Hoover Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...