Question about Oreck XL2800 Upright Vacuum Cleaner Cord Hook Upright Vacuum Cleaner Cord Hook

Open Question

Wiring a Johnson motor in a Oreck upright with 2 light harness?

I need to know how to wire the common Blk wire to the motor? Diagram I have shows the common Blk wire going to the white power wire to light harness. I don,t want to damage the motor by wiring it wrong

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Wiring

first, what is the model number? I'll shoot you a wiring schematic.

Posted on Dec 07, 2007

Ad
reddevil6
  • 1673 Answers

SOURCE: Wiring

Here are the 4 different wiring for new Oreck motors.
2e7c587.jpg

Posted on Apr 07, 2008

Agent Don
  • 310 Answers

SOURCE: Oreck XL

I would advise you to ALWAYS to FIRST UNPLUG THEIR VACUUM before beginning any service procedure. The motor has 5 wires to the motor as stated in the Oreck owners manual, tow are for the headlights, one is a ground wire, and the other two are for the motor. There are two screws that hold in the Oreck motor and a good suggestion is to use tape the wires leads and mark the wires so that you will not make a mistake as you take it apart and reassemble the motor. That way you will not make any mistakes, whether or not you have wires for a headlight or not, the rules are the same. Also refer to the owner’s manual schematic and the exploded view. Questions? 1-800-989-3535
www.Oreck.com

Posted on Apr 09, 2008

Agent Don
  • 310 Answers

SOURCE: wiring diagram Oreck XL2

http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=650346
Wiring diagram Oreck XL2
Posted by geohil on Jun 06, 2008
Can I get a wiring diagram of the handle on an Oreck XL 2.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Oreck XL Ultra Bagged Upright Vacuum. The best place to get an owner’s manual is from the Oreck Factory of which I will supply for you listed below or you can download the owner’s manual from the Oreck Website. . I would check with your local Oreck dealer or vacuum dealer in your area to see what is going on. This is most unusual for this to happen. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.oreck.com/ Customer Service 1-800-989-3535
Monday thru Friday Hours are: 7:00 am to 7:00 pm CST
Saturday and Sunday Hours Are; 8:00 am to 4:30 pm CST
http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Posted on Jun 09, 2008

SOURCE: Oreck XL9100

see diagrams29c9e80.gif9924d45.gif3be73a6.gif

Posted on Oct 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to replace a motor on an xl classic. The bad motor is out and i do not know exactly where the wires connect on the new one. I need a wiring diagram.


Hi, it's Jeremy from Crucial Vacuum.

Below you will find a link for many different models of the Oreck XL Classic Bagged Upright Vacuum. I hope you find the link useful.

http://www.oreck.com/PUG/76054-01-REV-A-U2251-CLASSIC.pdf

If you would like further assistance, please feel free to give us a call at 877.750.9239. We have helpful and friendly customer care representatives on the line ready to assist you.

Jeremy Lerner
Crucial Vacuum Customer Care
http://www.crucialvacuum.com

May 22, 2014 | Oreck XL® Classic Bagged Upright Vacuum

1 Answer

Need to wire motor for oreck xl upright


Your new motor should be very similar to the old motor. Compare the two motors to see if you can determine where each wire on the old motor should go on the new motor. If you are not sure it may save you money to have it wired by a qualified repair person. If you hook it up wrong it may damage the new motor and/or other electric components of your vacuum.

Mar 03, 2014 | Vacuums

2 Answers

Ametek wiring diagram for a Oreck XL21 600 ECB


I cannot find a wiring diagram from where I am located right now, but I do know that the black wire coming from the power cord goes to the top side of the motor when you have it laying upside down with the cover off, and it will go to the tab towards the back of the vacuum. Sometimes they put a black dot beside the tab and if that is there you put your wires from the power cord on those. You will also have two wires coming from your light bar in front and the white wire will usually have a piggy-back terminal that your white wire from the power cord attaches to as well. If there are no black dots beside the terminal tabs the white wires will connect to the bottom terminal on the opposite side from the black power cord wire. It will usually be on the lower side of the motor as well. The black wire from the light bar will go on the remaining terminal tab as there is usually only three tabs on the motor. I will check back later this week to see if this has helped you and if not I should be able to get a diagram this weekend.

Sep 22, 2013 | Oreck Vacuums

1 Answer

Need wiring schematic for ametek 119550


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. They explicitly stated that they can't provide any wiring information for safety and liability reasons.

I found the Ametek schematic which shows the LINE and TAP locations on the motor.

Note: I have a 2600HH XL with 2 headlights.

Connect as follows:

3A, LINE: White lead w/piggy back terminal from light harness #1 & white lead from the power harness to the piggy back terminal
2A, TAP: Black lead from light harness #1
3B, LINE: White lead w/piggy back terminal from light harness #2 & black lead from the power harness
2B, TAP: Black lead from light harness #2

9f6a42fa-778c-4d92-87ed-8fafaf1adc57.png

Dec 13, 2012 | Vacuums

1 Answer

Clear oreck schematic


Here is Oreck's motor wiring diagram, if it isn't big enough to make out, give me your email addy and I will send it to you.
c409045.jpg

Oct 01, 2008 | Oreck XL21 Bagged Upright Vacuum

2 Answers

Wiring diagram Oreck XL2


http://geeksquad.fixya.com/ThreadView.aspx?prdid=19810&thid=650346
Wiring diagram Oreck XL2
Posted by geohil on Jun 06, 2008
Can I get a wiring diagram of the handle on an Oreck XL 2.

Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Oreck XL Ultra Bagged Upright Vacuum. The best place to get an owner’s manual is from the Oreck Factory of which I will supply for you listed below or you can download the owner’s manual from the Oreck Website. . I would check with your local Oreck dealer or vacuum dealer in your area to see what is going on. This is most unusual for this to happen. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

http://www.oreck.com/ Customer Service 1-800-989-3535
Monday thru Friday Hours are: 7:00 am to 7:00 pm CST
Saturday and Sunday Hours Are; 8:00 am to 4:30 pm CST
http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
Thanks, Don the Vac Man
Go Ahead. Use Us.

Jun 06, 2008 | Oreck XL Ultra Bagged Upright Vacuum

3 Answers

Wiring


Here are the 4 different wiring for new Oreck motors.
2e7c587.jpg

Apr 04, 2008 | Oreck XL Ultra Bagged Upright Vacuum

2 Answers

Wiring Schematices


I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. They explicitly stated that they can't provide any wiring information for safety and liability reasons.

I found the Ametek schematic which shows the LINE and TAP locations on the motor.

Note: I have a 2600HH XL with 2 headlights.

Connect as follows:

3A, LINE: White lead w/piggy back terminal from light harness #1 & white lead from the power harness to the piggy back terminal
2A, TAP: Black lead from light harness #1
3B, LINE: White lead w/piggy back terminal from light harness #2 & black lead from the power harness
2B, TAP: Black lead from light harness #2
0d8cd9ff-8942-4773-a1fa-32c87905b735.png

Mar 31, 2008 | Oreck XL Ultra Bagged Upright Vacuum

2 Answers

Wiring


backwards wiring. The motor will still run but the lights keep going out right?

Oct 23, 2007 | Oreck XL Ultra Bagged Upright Vacuum

Not finding what you are looking for?

Open Questions:

Oreck XL2800 Upright Vacuum Cleaner Cord Hook Upright Vacuum Cleaner Cord Hook Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oreck Vacuums Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18394 Answers

Kory Ronning

Level 2 Expert

60 Answers

Randy Schumann
Randy Schumann

Level 2 Expert

391 Answers

Are you an Oreck Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...