Question about Dymo DateMark Date/Time Stamper

1 Answer

Dat stamp not stamping

It flashes P.Reset but when I take the back off and press the reset it still flashes the same message.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the exact same problem. I took the back off of the stamper and like some others, I pushed the reset button with a pen. Surprise it worked!!! I am now able to date stamp my "stuff".

Hope this helps somebody.

Donna

Posted on Mar 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Low ink message


There isn't a reset button, just agree with the printer and push the "OK" or Cancel button, and keep on printing. Long story made short, most ink cartridges come with pre-stamped ink levels or expiration date, that you or I can't change. That the price you pay for superior tech and why ink cost so much. I hope that helps.

Mar 16, 2014 | Canon Pixma MX452

1 Answer

My printer will not print the orange light keeps flashing what can i do i got a refill cartridge


Hello.
Hold down the Stop/Reset button for approx 10 to 15 seconds (it has a red triangle stamped on it).
This dis-ables the ink level monitoring and allows you to print.
Regards GM

Jul 15, 2011 | Canon Pixma iP2700 InkJet Photo Printer

1 Answer

I had a roll of stamps in the Dymo labelwriter and when I pressed print somehow one of the stamps got caught in the label machine and have not been able to take it out. I need help!!


I have had this problem too. Lift the top cover, pull off the front cover. On the side with the jammed stamp, that piece can lift up to reveal the roller under it. You should be able to remove the stamp.

Apr 25, 2011 | Dymo LabelWriter Thermal Printer

1 Answer

Error message on stamps.com says: error initializing printer. I have used this printer lots and lots of times and this just started popping up.


ok 2 things either your firmware is outdated or your driver... i do have the same problems due to my driver is not correct...plus when i updated the driver i forgot to set printing orientation and paper size


first go to
http://www.seagullscientific.com/aspx/thermal_95.aspx
scroll down to zebra click download
then install it
you will see 2 printer in your printer and fax in control panel

right click on the LP2844 (not the Zdesign LP2844)
select printing preference

go to page setup tab
choose 4x6 from the drop down menu in(stock)

then apply
also dont forget to go to option to set the darkness uncheck the use current printing setting
go for 12- 14 the default setting is to light sometime might not scan..by usps...


since everytime you updated the driver ...your setting might go on default...that why you'll need to go back and reset the printing pref...

after i did it ...the stamp.com doen't have problem at all



hope this help
http://www.etsy.com/shop/iamyot

Oct 06, 2010 | Zebra LP 2844 Thermal Printer

2 Answers

My dymo datemark stamp says "reset" but we have no idea how to do it?


Take off the back cover and insert the tip of a pen or paper clip in the little button between the 3.0 volt battery door and the AA batteries. It is "printer reset" around the little hole. This should work. It works unless something is wrong with the ribbon of letters that can get stuck. I'm trying right now to get my to reset using this solution (that has worked previously) but it is not. So it is a **** shoot!

Jan 28, 2010 | Dymo DateMark Date/Time Stamper

1 Answer

How quickly do the AA batteries run down in the DYMO Datemark. I just started using a new one this morning and have stamped maybe 50 times and have now received the flashing p.reset


Mine usually last at least 6 months. But I am careful to lean it back slightly to make sure It's not touching the switch on the bottom, and I only use fresh energizer batteries.

Jul 02, 2009 | Dymo DateMark Date/Time Stamper

1 Answer

Dymo Twin Turbo Labelwriter not printing stamps


This is the response from dymo stamp. I did as they said and am now printing stamps again.
**************************
We have seen this cause problems with the .NET framework Microsoft uses and Dymo Stamp uses. Follow these steps to correct it Step 1: Download Microsoft Windows Installer CleanUp Utility
============================================
1. Visit:
http://download.microsoft.com/download/E/9/D/E9D80355-7AB4-45B8-80E8-983A48D5E1BD/msicuu2.exe
2. Save the file on the Desktop.
3. Please double click the msicuu2.exe file to install it on the computer.
Step 2: Remove .NET Framework
========================
1. Click Start -> (All) Programs->Windows Installer Clean Up.
2. Please locate and remove Any .NET Framework 2.0 software.
After that, please perform the following suggestions to reinstall .NET
Framework 2.0 and its updates. Step 3: Reinstall .NET Framework Version 2.0 SP 1
================================================== ==============
Please download and install the following

Microsoft .NET Framework 2.0 Service Pack 1 (x86
http://download.microsoft.com/download/0/8/c/08c19fa4-4c4f-4ffb-9d6c-150906578c9e/NetFx20SP1_x86.exe
Note: When the "File Download" window appears, please click Save, and follow
the directions to save the file on the Desktop. After downloading all the
setup files, please double-click on each one to install them.

Apr 15, 2008 | Dymo LabelWriter Thermal Printer

1 Answer

Englcdt.dat error message


Got the same VRR.2 ERROR message, but when I reset (hold 6 and enter and the same time for a few seconds) it went back to the main screen. Hopefully I didn't clear any important information!

Mar 24, 2008 | VeriFone OMNI 3200 (P092-101-10) Printer

1 Answer

Dymo LabelWriter 400 Turbo/Postage Issue


Yes, you are indeed doing something wrong. In terms of the "free" electronic postage offer, what you want to sign up for is the "DYMO Stamps" program, offered via endicia (this is different from endicia's other PAID programs...just be aware).

Simply put, just google "dymo stamps" and the first hit will bring you right to the sign-up location you want.

Just to clarify, unless you have a special program I'm not aware of, stamps.com is most definitely NOT free. They require a monthy fee (of course, they do have a free first month if that's what you're talking about). Regardless, stamps.com DOES work with the LabelWriter 400...but just not with the special "Dymo Stamp Labels" (these "stamps" only work with the free monthly servcie I mentioned earlier, "DYMO Stamps"). You can print up postage/labels via stamps.com just fine using the other size 2-part or 3-part labels sold via stamps.com or dymo.com's store.

good luck!

Mar 15, 2008 | Dymo LabelWriter 400 Turbo Thermal Printer

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dymo Printers & Copiers Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Ed Mac

Level 3 Expert

709 Answers

Jax Planet
Jax Planet

Level 2 Expert

921 Answers

Are you a Dymo Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...