Question about Keurig Elite B40 Coffee Maker

2 Answers

How to reset keurig b40

All lights are on and blinking. holding lights down or on and off in certain sequences didnt work. is there a reset button or sequence somewhere?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 5 Answers

1. There is some confusion over models. I've seen "B40" models and instructions with only one size cup button, both labeled B40. I own one stamped "B40" on the bottom, and it has two buttons -- small and large. FWIW, small = 8 oz, large = 10 oz.

2. These reset instructions from another site seemed to do something
What to Do If Your Keurig Won Brew Cup Barista

So.. this is what I did that worked for mine: 1) Hold down Auto-Off and LARGE cup at same time. (all lights should hold steady ON) 2) press SMALL cup while still holding Auto-Off and LARGE cup 3) Release all three, press LARGE cup again.. all lights should go off. 4) Unplug for about 5 - 10 second, plug back in. SHOULD WORK!

3. On *_my_* B40, remove the K-cup, close the door, fill the reservoir. Unplug and replug the B40. All lights should be off.

Pressing "Auto Off" and "Large Cup" together will turn on 3 lights (Heating, Add Water, Power) for about 3 seconds. Doesn't matter how long the buttons are pressed or what order they are released.

I tried lots of add-on combinations: e.g. press button x, press x multiple times, press x while lights are still on, press x after lights are off, press buttons x and y together, press x then y, press x and/or y while still holding Auto and Large, release Auto but not Large and press x, etc.

Nothing gave any confirmation that a reset was accepted. All lights always turned off after 3 seconds. Maybe Reset is only 1 step, i.e. Auto+Large together?

Posted on Mar 28, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,511 Answers

Pull plug, Put pug back in, hoild star 5 seconds, prime and flush.

Posted on Feb 06, 2014

  • Jared
    Jared Mar 28, 2014

    The B40 brewer has no star key. This must be for another model.

  • Jared
    Jared Mar 28, 2014

    More info: These seems to be a B40 model with only one size cup button. (I own one stamped B40 with 2 different size buttons). Maybe this referrs to just the one size cup B40 version.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: keurig b40

I dont think these machines are worth the money at all.

Posted on Aug 16, 2008

  • 1 Answer

SOURCE: keurig elite b40 cup lights don't flash. Both are

Lift the handle to open the k-cup holder and then close it back up. The coffee mug lights should begin to blink for you.

Posted on Dec 03, 2009

  • 2039 Answers

SOURCE: how do you descale the keurig B40

use descaling product not vinegar ,vinegar remove calcium in little piece descaler melt calcium 1 part descaler 1 part water fill water container start machine for a few second turn off let it seat for 15 minute repeat untill empty to reset the lightnormally its maneer of pressing the on button
i get back to you on that one pierre

Posted on Feb 24, 2008

  • 1 Answer

SOURCE: All LED lights flashing and the brewer does not work

Just got my fixed from tech support... the following is the procedure that works:
1. Hit auto off and small cup at the same time and release hit small cup three times, when it works the only light showing will be the descale light....
2. hit small cup then auto off, then release small cup and then auto off, when this works lights on will be the power button light and the descale light.....

ALL OF THE ABOVE DURING THE PROCEDURE MUST BEEN DONE FAST OR RAPIDLY....

3. With both of the above lights on unplug for about 3 to 5 seconds... and then the brewer comes to life.. and WORKS


I am now drinking a great coffee brew and enjoying it... This does work, but you have to push the buttons in the sequence I have listed and FAST!!!!!!

Posted on Feb 25, 2009

cmccune04
  • 213 Answers

SOURCE: need parts list for ELITE B40 KEURIG coffee maker

Should be listed in your manual. If you need parts check this out.

This is actually an ebay store. They have any Keurig part you could possibly need! It's the only steady keurig part business operating right now. Prices are fair products are in great condition. Seller has 100% positive feedback with 100's of satisfied customers who voiced their opinions of them.

They have parts for Keurig B30 mini, B40 Elite, B60 Special Edition, B70 Platinum, and B77

http://www.igotsweetdeals.com or

http://stores.ebay.com/Igotsweetdeals

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The power windows are not working on 3 doors. What could be the problem? Just had a dead battery and jumped it off.


Most likely the RX lost the ECU program/ configuration. Need to reset the config. It is a sequence of buttons that need to be pressed.
You have to do the exact sequence of each door as it blinks or you cannot use your windows. Here are the steps.

first the driver window button will blink. lower the window half way down then raise the window up to max and hold the button for 5 seconds. Then the front passenger window button will light up and you do the same thing for each door as it lights up. It goes driver, front passenger, rear passenger side then rear driver side then do your sunroof by hitting the tilt button hold for 5 seconds and that calibrates all the windows.

Mar 07, 2010 | 2005 Lexus RX330

2 Answers

Light on dash windshild wipers &two other keep blinking sometimes after a while they go off for a litte than go back on


YOU HAVE TO TURN THE AIR ON HIGH - FRONT AND BACK AND THEN HOLD DOWN ALL THREE BOTTOM BUTTONS AT THE SAME TIME THREE TIMES FAST AND HOLD ONE FULL MINUTE ON FORTH PUSH AND THEN THEY SHOULD STOP BLINKING I HAD TO MESS WITH MINE SEVERAL TIMES TO GET THIS TO WORK....BUT FINALLY GOT IT AFTER 20 MINUTES OF DOING IT OVER AND OVER. HAS TO BE DONE JUST RIGHT TO RESET THE DASH LIGHTS.

Nov 07, 2009 | 1998 Dodge Grand Caravan

2 Answers

Replaced ink cartlidge and now wont print


After replacing the ink cartridge you should print the alignment page to work product perfectly.
Follow the below instructions to print alignment page:

  1. Turn on the HP PSC 1200 or 1300 series product.
  2. Disconnect the USB cable from the all-in-one.
  3. Press the sequence of front panel buttons below to start the print cartridge alignment process. The button-press sequence must be completed within ten seconds. It might take several tries to complete the sequence within ten seconds.
    1. Press and hold Cancel .
    2. While holding Cancel , press On .
    3. When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both buttons.
    4. Press Cancel again.
    5. Press Copies .
    6. Press Paper Type .
    7. Press Color Start Copy . The alignment page will begin printing. If the alignment page does not print, repeat the button-press sequence in this step.
  4. When the alignment page has printed, place the page face down on the scanner glass and press Scan . The alignment is complete when the On light stops blinking.
  5. Reconnect the USB cable.


If the issue still persists, perform semifull reset by following the below instructions

  1. Unplug the power cord from the wall outlet.
  2. Unplug the power cord from the back of the all-in-one.
  3. Wait 30 seconds and plug the power cord back into the wall outlet.
  4. Plug the power cord to the back of the all-in-one.
  5. When the lights begin to flash, press and hold the On/Resume and Number of Copies Buttons.
  6. When only the On/Resume light is flashing, release the buttons.
  7. When the On/Resume light is steady, the reset is complete.




Oct 12, 2009 | HP PSC 1350 All-In-One Thermal Printer

1 Answer

65 in Mitsubishi rear projection tv won't power on.


Go to the set and when turning it on doesn't work push and hold down the MENU and INPUT buttons at the same time until the LED starts blinking. It should be a two blink sequence like 1 blink pause 2 blinks long pause and then repeats. Repost the blink sequence and that will narrow down what the microprocessor thinks is the problem area.

Jun 09, 2009 | Mitsubishi WS-65809 65" Rear Projection...

1 Answer

My panasonic big screen wont turn on


find out if someone can push the rest button on the side somewhere in a certain sequence

Feb 07, 2009 | Mitsubishi WD-52725 52". Rear Projection...

1 Answer

ASKO Dishwasher F2 light flashing


Hold the Rinse button for 5 seconds to reset.

Jan 19, 2009 | Asko D1776 Built-in Dishwasher

1 Answer

How do I get a alingment test


HP PSC 1200 and 1300 series:
  1. Turn on the HP PSC 1200 or 1300 series product.
  2. Disconnect the USB cable from the all-in-one.
  3. Press the sequence of front panel buttons below to start the print cartridge alignment process. The button-press sequence must be completed within ten seconds. It might take several tries to complete the sequence within ten seconds.
    1. Press and hold Cancel .
    2. While holding Cancel , press On .
    3. When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both buttons.
    4. Press Cancel again.
    5. Press Copies .
    6. Press Paper Type .
    7. Press Color Start Copy . The alignment page will begin printing. If the alignment page does not print, repeat the button-press sequence in this step.
  4. When the alignment page has printed, place the page face down on the scanner glass and press Scan . The alignment is complete when the On light stops blinking.
  5. Reconnect the USB cable.

Jan 14, 2009 | HP PSC 1210 All-In-One InkJet Printer

2 Answers

Lock Light Blinking


silly question but did you try holding the control lock button(perhaps its the heated dry button) in for 3 secs???? sonds as if the CONTROL LOCK has benn activated( child lockout)

Jan 14, 2009 | Kenmore 24 in. 15932 Built-in Dishwasher

1 Answer

Actually for a HP deskjet 990cxi


Alignment:

1. Turn on the HP DeskJet.
2. Disconnect the USB cable from the all-in-one.
3. Press the sequence of front panel buttons below to start the print cartridge alignment process.
The button-press sequence must be completed within ten seconds. It might take several tries to complete the sequence within ten seconds.
1. Press and hold Cancel .
2. While holding Cancel , press On .
3. When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both buttons.
4. Press Cancel again.
5. Press Copies .
6. Press Paper Type .
7. Press Color Start Copy .
The alignment page will begin printing.
If the alignment page does not print, repeat the button-press sequence in this step.
4. When the alignment page has printed, place the page face down on the scanner glass and press Scan .
The alignment is complete when the On light stops blinking.
5. Reconnect the USB cable.

Jun 03, 2008 | HP DeskJet 940c InkJet Printer

1 Answer

Clean ligh is blinking


youll need to remove the bottom acess panel of d/w there should be an extensive trouble shooting guide tapedto back of panel in a sleeve, lotsa good stuff in there. depending on buttons its going to repuire pushing a sequence. "
sani-rinse---heated dry--sani rinse--heated dry.
it will enter a diag mode "all lights will light up" wait a few secs and then cancel cycle .. if happens a again or with frequency, then call a servicer, you have a problem, first time chaulk up to a fluke

Mar 22, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Keurig Elite B40 Coffee Maker Logo

5,723 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keurig Coffee Makers & Espresso Machines Experts

Lisa
Lisa

Level 2 Expert

92 Answers

Jason

Level 2 Expert

211 Answers

Cindy Wells

Level 3 Expert

5159 Answers

Are you a Keurig Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...