Question about Husqvarna Chain Saw Models 371, 372xp

1 Answer

New 372xp seized up

Saw is dead, how much money to rebuild?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Husqvarna Master
  • 2,239 Answers

Genuine cylindere and is is very expensive, there are plenty of after market cylinders available at very good prices, however you pay your money and take your chance, before fitting any new parts you need to confirm why it siezed in the first place or it is just as likley to go again.

Posted on Jan 04, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Husqvana 371k starts but stops when i put choke in and throttle on. why?


Is there fresh fuel in the tank? If the fuel has been there for over 2 months dump it out and put in fresh fuel and try starting again.

Jul 31, 2014 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

Glastar allstar grinder wheel not turning


You may have seized the bearings. Either replace the motor or rebuild using new bearings if the motor even works

Nov 29, 2013 | Glastar Diamond Star Grinder w/extras -...

1 Answer

Husqvarna 372xp won't start... Mysterious


I recently bought a brand new 372XP and spent the first day trying to start it as per the instruction manual with no success, never even fired once. Removed the plug to find plenty of fuel and that the plug has a good spark. Left it until the next day mainly to allow my arm to recover (& scour the internet for clues). I found a forum that said not to use the decompressor and sure enough without the use of the decompressor button it fired first go with the choke on then I reset the choke & it ran properly on the second pull. The decompressor button can be reset with fine nosed pliers or removal of the top cover by undoing three screws. Good luck it's a great saw once you know how to start it.

Apr 01, 2012 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

Repairmanuelhusqvarna36


Send me an e mail address and i will send PDF file with thw shop manual.

Oct 08, 2011 | Husqvarna Operator's Manual 365 372xp ...

1 Answer

My 372xp was in use and started reving up at full rpms and wont kick down. What could i do ?


check idle settings, if its ok check all valves and carburator assy is ok, check gaskets and sealings.

Mar 25, 2011 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

How much oil do you have to mix with fuel for a Husqvarna 365 special chainsaw?


50:1 is the fuel to oil ratio. Most oil bottles have dispenser guides for a gallon of fuel. Be sure to use a modern synthetic saw oil and fresh gas. Shake the container thoroughly each time just before adding fuel to the tank to prevent oil starvation. Hope this helps!

Nov 13, 2010 | Husqvarna Operator's Manual 365 372xp ...

1 Answer

Piston of a ts400 cutquik saw is seized in the housing


What did you expect? Find a engine rebuilder and get ready to spend about 75% of a new replacement.

Jul 16, 2009 | Hand Tools

4 Answers

New or used motor for a Craftsman 10" table saw


Sears no longer sells repair parts for this motor, only the whole motor as a replacement part, and it is $140.00, but you can buy replacement bearings from drillspot.com the bearing needed is an Enduro 6200 zz c3

Apr 26, 2009 | Craftsman 10" Table Saw

Not finding what you are looking for?
Husqvarna Chain Saw Models 371, 372xp Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

608 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...