Question about Norelco G270 Beard Trimmer

Open Question

How do i unlock my norelco beard shaver

How to disengage the travel lock

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: How do I change the Battery in My Norelco T3000 Beard Trimer

twist the head and the body.

Posted on Jul 06, 2009

  • 10865 Answers

SOURCE: Using Norelco 3801XL shaver in Europe

hello. In order to use these devices in Europe you need a power adapter. Go to this link to learn all about it
http://goeurope.about.com/od/electricityineurope/tp/power_adapters.htm
Joe. Please rate my answer as very helpful. thank you

Posted on Mar 25, 2010

brector3
  • 1598 Answers

SOURCE: Norelco 835rx unused for 10 yrs, worked 1st time, then not.

The battery pack is, likely bad and will need replaced. Batteries don't hold up well sitting around for 10 years. The stress of charging may have finished off the batteries completely. When the batteries short out internally, the shaver wont run from the cord either. Before ordering batteries you'll want to make sure the old ones have not corroded badly and ruined the circuit board. To check it out, remove the four screws on the back and remove the back cover. Lift out the circuit board and inspect it to make sure there are no burns.

If everything looks to be in good shape, installing a new battery pack will probably be all you need to do. You will fin the correct battery pack at shaveroulet.com. See link below

http://shaveroutlet.com/shaver-battery-pack-for-most-norelco-more-p-278.html

Posted on Apr 06, 2010

EwingElect
  • 276 Answers

SOURCE: Norelco 5825XL Replacement Blades

HQ5 is not compatible with HQ55. I've checked the Service Manual and HQ5 is the correct part. It's got to do with the driving mechanism for the head.

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Disengage mulch drive


Have you looked beneath the deck with someone engaging or disengaging the blade lever? Get underneath and observe how the belt travels from the engine pulley back, and follow it in the loop it travels to see how it works with the lever engaged and disengaged.

Jun 08, 2013 | Craftsman 17.5 hp 42 in. Deck Lawn Tractor...

1 Answer

Husqvarna pto problem(?) disengaged blades to travel, would not engage after. Battery dead when checked after shutting off engine and wouldn't restart


Hi, first charge or replace the battery if necessary then check that the mower is charging the battery. The pto is probably fine but it needs battery voltage to engage. If the mower has stopped charging the battery may have had enough voltage to hold the pto in until you disengaged it but not enough to re engage it. Regards Phil.

Sep 06, 2012 | Garden

1 Answer

My LS1013 saw head is in the down storage position and will not raise up. It is not pinned.


you need to depress it fully to disengage the lock. If the head does not depress enough there is a screw that you would need to loosen on the left hand side to allow for the head to travel lower. Make sure there is nothing under the blade to affect movement before trying bolt.

Jan 23, 2012 | Makita Saws

1 Answer

Disengaging shift lock


If you mean the gear shirt is stuck and you want to use the shift lock, then beside your gear shift there will be a spot that says disengage shift lock, pry open the cover and usually you can disengage it with a screwdriver sometimes when you pop the cover there is a switch that you can push to disengage shift lock hope this helps you

Jan 05, 2011 | 2002 Hyundai Accent

1 Answer

4 wheel drive will not disengage


take a standard screwdriver apply pressure to the whole switch panel towrds the drivers window then repeatedly push the 2 wheel drive button until the low lock button flashes then keep on pushing 2wheel drive button til it shifts you can tell its out by cranking steering wheel all the way to either end of travel and move foward no binding means your out

Sep 25, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

The clutch on my 1998 legacy has just been replaced, but there is about four inches free travel in clutch pedal before it engages the throwout bearing. This leaves only about 2-3 inches at the bottom of...


You want to shorten the cable. Loosen the lock nut.Turn the cable adjuster clockwise to shorten the cable. This takes some skill, and knowledge to get the clutch adjusted just right. You want about 1/2 inch of free play in the pedal. All of this varies according to the wear on your clutch. You say your clutch is new, so acheving a proper adjustment should be no problem. Keep tweaking the adjustment to get it catching where you like it.

Sep 02, 2010 | Subaru Legacy Cars & Trucks

2 Answers

4 wheel drive will not disengage.


If you have tried shifting stopped and moving, then I'd say the transfer servo could be broken. It is the motor on the transfer case that shifts it in and out of four wheel drive. If you know how to use a voltmeter, test the wires that run to the servo to see if it is getting the signals it should be. Newer vehicles usually have a computer associated with the transfer case motor. You could have the car plugged to a tester at auto zone to see if it is giving a code.

Dec 14, 2008 | 2000 Isuzu Rodeo

2 Answers

Passengerside front wheel locking up on reversing 1998 Discovery


Hi, one posibility is that your brake calipper can be locking up ,you can check it by lifting the vehicle from that side and have someone to apply and release the brake it should roll free as soon as the brake is released......good luck......

Nov 15, 2008 | 1998 Land Rover Discovery

1 Answer

Button


The button with a "D" with a circle around is for engaging and disengaging overdrive. Your transmission typically will have 4 forward driving gears...by having overdrive disengaged your car will not go into the 4th gear. Disengaging overdrive should only be used when towing or traveling in mountainous terrain.

Jun 29, 2008 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
Norelco G270 Beard Trimmer Logo

Related Topics:

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Norelco Health & Beauty Experts

shaveroutlet.com
shaveroutlet.com

Level 3 Expert

1598 Answers

Robert McClure

Level 2 Expert

160 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14534 Answers

Are you a Norelco Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...