Question about Evenflo Exersaucer Triple Fun Active Learning Center

Open Question

Evenflo exersaucer triple fun won't spring back

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I need assembly directions for evenflo exersaucer triple fun.

1. Remove toys and seat from the exersaucer.
2. Fold exersaucer, but do not let the tray lock to the base. With exersaucer flat on the floor, twist each leg assembly (B) fully clockwise until it stops. Fully depress one of the pedestal locking tabs (C) then push on the leg assembly (B); leg will partially fold. Repeat this for all four legs. After pressing the fourth pedestal locking tab (C), the Exersaucer will fold with the tray (D) rotating toward the base (E). Make sure all four tray locks. (F) are locked onto the base before trying to carry exersaucer.
3. Place your fingers beneath the legs (A) push upward to disconnect the leg assemblies from the pedestals (B). Repeat for all 4 leg assemblies.
4. After all four legs have been disconnected from the pedestals, remove tray assembly (C) from the base (D).
5. Turn tray (C) upside down and remove both end caps (E) from beneath.
6. Squeeze both locking tabs (F) on each side of the tray to disconnect and seperate the tray halves (C). 7. Connect tray halves (C) to form activity table.
7. Connect tray halves (C) to form activity table.
8. Rotate leg assemblies (A) fully clockwise until they lock into postition. Make sure all four legs lock (G) are locked properly into the uper leg pedestal (H). Also make sure all four leg locks (I) are sticking out past the edge of the tray.
9. Turn table over and install two end caps (E). Make sure both end caps lock into place. NOTE: one end cap installs from above and the other installs from below.
10. Install toys on activity table. If desired, adjust table to the appropriate height for your child. IMPORTANT: NEVER use stage 3 without end caps!

Posted on Apr 19, 2009

  • 286 Answers

SOURCE: I am needing an instruction

hi
here is a page link to instruction download
near to bottom of the page

https://plweb.evenflo.com/product_search.aspx?txSearchModelNo=6231883&txSearchDOM=1/1/2010

Posted on Oct 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Convertexersaucer to activity table


Here's an article along with photos and video on converting the Evenflo Exersaucer to the activity table: How to Convert the Evenflo Exersaucer into Stage 3

Apr 08, 2015 | Evenflo Exersaucer Triple Fun Active...

1 Answer

How to convert evenflo exersaucer


Here's a step-by-step article for converting the Evenflo Exersaucer. It has photos and videos. How to Convert the Evenflo Exersaucer into Stage 3

Mar 01, 2015 | Evenflo Exersaucer Triple Fun Active...

1 Answer

How do I convert exersaucer to activity table


Here's an article explaining how to covert the Evenflo exersaucer into the stage 3 activity table. How to Convert the Evenflo Exersaucer into Stage 3

Sep 01, 2014 | Evenflo Exersaucer Triple Fun Active...

1 Answer

How to convert To stage 3


Here's an article on how to convert the Evenflo Exersaucer to the stage 3 activity table: How to Convert the Evenflo Exersaucer into Stage 3

Jan 16, 2014 | Evenflo Exersaucer Triple Fun Active...

1 Answer

I need an instruction manual for the Evenflo Triple Fun model #6231711 (manufacture date unknown - sticker is missing).


Here's an article that outlines the steps for converting the Evenflo Exersaucer to stage 3. It has photos and videos. Also, if you compare your end cap with the ones in the video, you'll see whether or not your end caps were replaced. How to Convert the Evenflo Exersaucer into Stage 3

Nov 27, 2011 | Evenflo Exersaucer Triple Fun Active...

2 Answers

I am needing an instruction manual for an Evenflo Exersaucer Triple Fun 25800496 08/06


hi
here is a page link to instruction download
near to bottom of the page

https://plweb.evenflo.com/product_search.aspx?txSearchModelNo=6231883&txSearchDOM=1/1/2010

Oct 26, 2010 | Evenflo Exersaucer Triple Fun Active...

1 Answer

How do i put the seat back on my evenflo exersaucer


There are several models of exersaucers, but hopefully the seat attachments are similar. Here is a video from Evenflo showing how to assemble the product. This might help you.

http://www.evenflo.com/resource.aspx?id=467&rcid=19

Sep 29, 2010 | Evenflo Exersaucer Triple Fun Active...

2 Answers

I need assembly directions for evenflo exersaucer triple fun.


1. Remove toys and seat from the exersaucer.
2. Fold exersaucer, but do not let the tray lock to the base. With exersaucer flat on the floor, twist each leg assembly (B) fully clockwise until it stops. Fully depress one of the pedestal locking tabs (C) then push on the leg assembly (B); leg will partially fold. Repeat this for all four legs. After pressing the fourth pedestal locking tab (C), the Exersaucer will fold with the tray (D) rotating toward the base (E). Make sure all four tray locks. (F) are locked onto the base before trying to carry exersaucer.
3. Place your fingers beneath the legs (A) push upward to disconnect the leg assemblies from the pedestals (B). Repeat for all 4 leg assemblies.
4. After all four legs have been disconnected from the pedestals, remove tray assembly (C) from the base (D).
5. Turn tray (C) upside down and remove both end caps (E) from beneath.
6. Squeeze both locking tabs (F) on each side of the tray to disconnect and seperate the tray halves (C). 7. Connect tray halves (C) to form activity table.
7. Connect tray halves (C) to form activity table.
8. Rotate leg assemblies (A) fully clockwise until they lock into postition. Make sure all four legs lock (G) are locked properly into the uper leg pedestal (H). Also make sure all four leg locks (I) are sticking out past the edge of the tray.
9. Turn table over and install two end caps (E). Make sure both end caps lock into place. NOTE: one end cap installs from above and the other installs from below.
10. Install toys on activity table. If desired, adjust table to the appropriate height for your child. IMPORTANT: NEVER use stage 3 without end caps!

Mar 20, 2009 | Evenflo Exersaucer Triple Fun Active...

1 Answer

Lost instructions to the evenflo triple fun excersaucer


put the bottom and top togather where the 3 holes are on top put the springs put the caps on and turn them. You will have to use a little pressure but they will turn

Dec 21, 2008 | Evenflo ExerSaucer SmartSteps ABC Stroller

Not finding what you are looking for?
Evenflo Exersaucer Triple Fun Active Learning Center Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Evenflo Toys Experts

ka4iup
ka4iup

Level 3 Expert

3957 Answers

john h

Level 3 Expert

12104 Answers

Bill Boyd

Level 3 Expert

42190 Answers

Are you an Evenflo Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...