Question about Whirlpool Washing Machines
Our Whirlpool Duet (model # WFW9150WW02) is stopping mid-cycle (on the rinse cycle) and beeping...door remains locked.
Posted by Anonymous on
F3E2 error, Wash light flashes 3 times then 2.
Took off front lower cover, Found Manual!!!
Unscrewed filter and was so full of trash, clean and reassymbled and now works just like new. Simple fix no parts at all needed.
Posted on Nov 22, 2014
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: whirlpool duet sport washer
F01 finally fixed after 2 repairmen and 2 circuit boards replaced/5 weeks of loaundromat! ! HINT have your repair technician check the boards. Be sure to have them especially check which wires are connected to which areas of the board. It could be that the wires are connected to the wrong place on the board. Good luck!
Posted on Sep 26, 2007
f22 is a door lock error try this hit cancel turn your dial to another setting, hit start and once it starts hit cancel again and it should unlock. thats what i did anyway.
If you're getting an F22 error, you will want to check anything to do with the door latch switch.
Posted on Mar 14, 2009
probably your door then, look at the door itself, at the latch is it broken? should form a complete square hole with four sides. if broken some part is probably inside lock asm. if complete, look at lock and determine if its in the lock position with door open, a arm will be up preventing the latch from going in. replace as necessary. Old duets (red lights) use standard lock asm same as GE and samsung. New duets (green lights) use whirlpool/new maytag unique asm. New locks come in two interchageable models, German (made in china) and Mexican, Mexican model is more troublesome, get german.
If lights flash during a cycle or other time, its giving a code, note the F code displayed
Posted on Jul 19, 2009
HI. this code represents a Long Drain issue.
If the drain time exceeds 8 minutes, the water valves are turned off and F02 is flashed.
Press PAUSE/CANCEL twice to clear the display.
NOTE: After 4 minutes the “Sud” error will be displayed, then 4 minutes later the F02 error code will be displayed.
• Check the drain hose and make sure it is not plugged or kinked
• Check the electrical connections at the pump and make sure the pump is running.
• Check the drain pump filter for foreign objects
• If the above does not correct the problem replace the pump
Posted on Oct 16, 2009
The display is actually reading "Sd", which is a Suds detect error. This is an indication that you have either used too much detergent, are using the wrong type of detergent, or you have an obstruction somewhere in the drainage system. The following link explains the error code and how to correct it:
There is a follow-on link included that explains the steps necessary to check the drain pump reservoir. Read through the information provided and let me know if you have any questions. I hope this helps you.
Posted on Feb 26, 2010
Tips for a great answer:
Jan 25, 2016 | Whirlpool Washing Machines
Jan 05, 2016 | Washing Machines
& Welcome to FixYa
I don't think it is any other board, I believe the CCU (central control unit)
has gone bad as it keeps on stopping mid cycle. If it was the Motor Control
Board (MCU) then the washer motor should have been causing problems (which isn't
the case) so replacement of CCU will be a great option. Please get back to me
if you have any other questions.
Sep 23, 2011 | Whirlpool Duet GHW9150P Front Load Washer
Jan 08, 2010 | Whirlpool Duet GHW9150P Front Load Washer
Jun 24, 2008 | Whirlpool Duet GHW9150P Front Load Washer
482 people viewed this question
Usually answered in minutes!