Question about Siemens WK61420GB Front Load Washer / Dryer

1 Answer

Machine stops during wash and rinse cycles. To compete the wash process I have to turn machine off and leave for a few seconds then switch on again, same with the rinses until it gets to the final rinse when it will complete the cycle without assistance

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

Please start by running the machine empty and see if you have the same problem. You might be overloading your machine

Posted on Jan 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Washer Doesn't Agitate


Don't be too sure the drive coupler hasn't failed or is failing

Jun 15, 2013 | Kenmore 24032\24036 Top Load Washer

1 Answer

Fisher and Paykel 7.5 washing machine keeps powering off during rinse and spin cycles


The pump has a thermal safety cut out on it.
If the pump gets too hot it cut out.
Just put a new pump in and your all going again.

Aug 05, 2012 | Fisher and Paykel Washing Machines

1 Answer

Machine will not spin or drain water.


I have a problem with my MW512AU. Sometimes it drains after wash cycle, but sometimes it sticks when it goes to spin, doesn't get up to speed, water comes on for about 10 seconds and shuts off, and it tries to spin again. If I hit the wash progress switch it goes directly to final spin and works ok. I then have to run a 2nd wash cycle to rinse the clothes. I also noticed a buzzing sound when I turn on the power point, which lasts about 3 seconds before stopping. It will come back on every 3-4 minutes for 30 seconds. This is with the machine power switch off. It powers on normally.

Mar 13, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Washing machine does not drain during rinse cycle?


Turn timer to rinse cycle. let fill up and agitate. when it stops agitating it should pause then start to pump water out. After about 2 minutes it should pause for 3-5 seconds then start again and spin. If it starts the first time and never stops it will just continue to pump but no spin. The 3-5 second pause allows the transmission to shift to spin. If it does not do this the problem is your timer. You may need to do this a few times to verify the problem.

If that is not the problem it is likely that you need a new clutch. You will need a technician to install a new clutch for you

May 17, 2009 | Whirlpool LSQ9600L Top Load Washer

2 Answers

Cold water will not stop filling during rinse


while the unit is filling in the warm cycle. reach behind and shut off the hot water tap.I bet the water flow stops filling, if so, you would need to change the inlet valve on the machine. You see, in warm, if the cold is not filling, you still hear the hot filling and the unit will advance. The rinse cycles are mostly "cold" only. if the valve is not opening it will not allow it to advance from the rinse section on the board.

Good luck!

Feb 16, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

F & P washing machine GW709AU not competing rinse cycle and then beeps and flashes light.


My Whirlpool washing machine is not stopping after completion of wash cycle instead it is repeating the cycle again. It is not consistent, but out of 3 washes 1 wash is happening that way...we are manually stopping machine by gaurding carefully when timer shows nearer to completion.

Sep 15, 2008 | Washing Machines

1 Answer

Whirlpool Washing Machine Quitting during rinse cycle


I would say that based on your problem description that the lid /door switch has a loose or faulty contact .. If you open and close it a few times..it starts to spin and yet when you open it.. it doesn't always stop the spinning.. It is either the switch or the actuator that bumps that switch.. That is where I would begin diagnosing the problem... Hope that helps..

Aug 30, 2008 | Washing Machines

1 Answer

Fisher and Paykal GWL 10 US - Stops before rinse


52. (00110100) Eco - Diverter Top-up Fault diverter valve made be stuck in half open position ,may be a mechanical obstuction or the wax filled solenoid that actuates it may be faulty .located under machine beside pump .

Jun 17, 2008 | Fisher and Paykel GWL11 Top Load Washer

3 Answers

1 beep per second and odd light sequence


there some simple solutions but may not always work but everyone should try. underneath when the water pump engage with the tub. there;s a white plastic clip press it out and turn the water pump. it will come off the tub. before doing this you should have the washer disconnected. have someone or put something under so the washer won;t fell on you while reaching down. sometimes debris gets stucks on the way from the tub to the pump. it insert your fingers inside once the pump is taken out and if you find debris take it out. put back the pump and connect the washer again. this can be a very simple solution it won;t work all the times. but what if it does. :)

Jun 14, 2007 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Beeping and odd light sequence


I have the same problem with my 603 washing machine stopping in the middle of a cycle and i would have to go and manually advance the wash. I have just replaced the top curcuit board with a new one. can you please help or offer a solution. Thank you.

Jun 14, 2007 | Fisher and Paykel GWL11 Top Load Washer

Not finding what you are looking for?
Siemens WK61420GB Front Load Washer / Dryer Logo

736 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

shaun taylor

Level 3 Expert

1450 Answers

Are you a Siemens Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...