Question about The Learning Company Black & Decker Everyday Home Repairs (BDH3844AE) for PC

1 Answer

Replace sheerpin on snowblower

I have a Sears snowblower and only 1/2 of the blade turns - I hit a steak and it looks like the sheerpin is broken on one side - don't have a manual and wonder if I can fix it myself.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Go to sears and ask tell the salesman whats wrong. he will tell how to fix it, sounds like you need a shear pin.

Posted on Feb 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to change shear pin


With the motor OFF, the shaft shouldn't rotate, so you should be able to rotate the auger by hand until the holes line up.

Mar 01, 2014 | Craftsman Sears Snow Thrower Manual Model...

1 Answer

Car boot won t open


Went through every site recently but couldn't get the answer.
For my 1985 Toyota corona the answer is.
Firstly open the boot.
1. Look at similar boot in open position.
2. Slide steak knife in at 45 degrees upwards from rear to front under the boot. Ensure the end of the blade is aiming at the lock.
3. Push steak knife handle to left.
Next fix the problem.
A. Search for defective component and replace it.
B. After replacing the basic lock a component still needed to be bent
to activate lock whilst key was turning.
Finally test boot without locking it.
Use screwdriver to click mechanism as if locking, before using key to unlock.

Jan 05, 2014 | Cars & Trucks

1 Answer

Continuous clunking when i engage the auger on my snowblower


check for bent blower and auger blades
check rear blower bearing, engine off( grab rear of shaft pull up and down) shouldnt move very much. if it does bearing bad

Dec 28, 2013 | Craftsman 22" 179cc* Dual-Stage Snowblower

1 Answer

CRAFTSMAN®/MD Electric Snowblower owner's


If this is a Craftsman product then you should be able to enter the model number here and get one.. The manual tab will be on the right after they find it for you. A lot of repair information is not available in manuals, but Sears manuals are known to have parts schematic breakdown lists and diagrams, plus you can purchase from the online parts breakdown lists.
http://www.searspartsdirect.com/partsdirect/index.action?psid=26132896&sid=PSx20071217x00001d&OVMTC=b&OVKEY=sears%20part%20direct&creative=726752&adcid=1987828

Jan 16, 2011 | Craftsman Garden

1 Answer

I just opened a 12"


As this is an unused machine, take it back to Sears for replacement (Sears used to have a 'satisfaction-guaranteed' policy--hope they still do)! It appears that the frame is for a smaller saw blade than 12". Good luck!

Nov 28, 2010 | Craftsman Garden

1 Answer

I have an old Sears Jig Saw, model 110 25710, that has a broken blade. I need a new blad and instructions on how to remove the broken one, and replace it with the new one. Can you offer any assistance?


Take a look at the point of blade locking to the tool. Should be 2 hexagon bolts. Using the right size tool, unscrew them carefylly, pull out the broken blade, go to your local hardware store, and get a new one that will have the same size on the tail. ( the side that gets inside the slide on the saw). Slide the new blade to the saw, and tighten the bolts back but do it equally twisting them in turns, half a turn each time to keep the blade staying straight.
Whole thing should last no more than 5 min. ( Remember to keep the power cable unplugged all the time you make the change. Your fingers are priceless).

Sep 08, 2010 | Sears Saws

1 Answer

Auger blades won't turn


You need what they call a "friction wheel" replaced.

Oct 31, 2009 | Garden

1 Answer

Broken off shear bolt stuck in snowblower


hit the pin out with a punch and a hammer after drilling off any part of the pin that might be impeding your progress. you might also have to put some juice into your swings because a nail is too soft

Jan 11, 2009 | Mtd 22" Yard Machine Push Mower

Not finding what you are looking for?
The Learning Company Black & Decker Everyday Home Repairs (BDH3844AE) for PC Logo

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top The Learning Company Computers & Internet Experts

k24674

Level 3 Expert

7993 Answers

kakima

Level 3 Expert

102366 Answers

Stitch85

Level 1 Expert

27 Answers

Are you a The Learning Company Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...