Question about Malber WD1000 Front Load Washer/Dryer

1 Answer

Getting the dryer to start after turning it off.

I just replaced my Haier Washer Dryer Combo with the Malber. I was able to wash a load of clothing and get the dryer to start right away after the wash. Unfortunately, after I turned the dryer off to take out some clothing I didn't want to dry, I cannot get the dryer to start up again. I waited 12 minutes and still nothing. Can anyone help?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Suggestion: Switch off wall plug and restart to dry.

Posted on Jun 28, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I dry clothes


Either hang them up wet or put in clothes dryer

Nov 26, 2014 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Malber WD1000 dryer timer starts running immediately when set, even in the middle of wash cycle


Call in the troops! You need to have the controller panel opened and checked for excessive lint and dirt. There is a short or two in that mess!

Dec 26, 2012 | Malber WD1000 Front Load Washer/Dryer

1 Answer

I just got a malber 1000 washer/dryer. Can it be used as a dryer only?


NO THIS UNIT USES CONDENSED DRYING AND WILL WET THE CLOTHES BEFORE IT EVEN TURNS ON THE HEATER. BASICALLY YOUR COMBO USES STEAM CIRCULATION THRU YOUR CLOTHES. AS THE SMALL WATER PARTICLES IN THE STEAM MOVE THRU YOUR CLOTHES IT COMBINES WITH SMALL WATER PARTICALS IN THE CLOTHES(THINK OF 2 WATER DROPS COMBINING ON YOUR WINDSHEILD AND HOW THEY ABSORB TOGETHER) WHICH RISE TO THE TOP OF THE TUB AND COLLECT INTO WATER AGAIN. THEY THEN ROLL DOWN THE SIDES OF THE TUB AND COLLECT AGAIN AT THE BOTTOM TO BE PUMPED OUT. BEFORE THIS PROCESS EVEN STARTS THE UNIT WILL ACTUALLY ADD WATER TO GENERATE THE STEAM. MOST PEOPLE FIND THAT IF THEY WANT TO JUST FRESHEN UP SOMETHING, IT WILL END UP DRENCHING WET IN THE FIRST FEW MINUTES.

Jan 18, 2010 | Malber WD1000 Front Load Washer/Dryer

1 Answer

We have the Haier XQG50-11 Combo VENTLESS Washer / Dryer 120 Volt and the problem we are having is that the clothes are not drying. The dryer itself gets plenty hot but the clothes are wetter at the end...


make sure your drum is turning,open it quickly and see if it's turning,also make sure you have good ventilation behind the dryer,let me know what you find-mike

Oct 15, 2008 | Haier Washing Machines

1 Answer

How do you DRY with the Haier washer/dryer


Have you tried lengthening the dryer cycle or running it at a higher temp? The usual culprit for wet clothes is not running a dryer long enough or hot enough. (I remember some stand-alone dryers (coin-operated with a fixed drying time per coin) that needed two cycles to dry stuff.

Jul 12, 2008 | Haier 14.3 lb. Washer/Dryer Combo

1 Answer

How much clorox 2 and fabric softener


DONT USE CLOROXE 2 ITS NO GOOD make sure you wash on cold / cold that makes the colr last and no shrinkingit takes a full lid on full load half lid on medium and 1/4 on small load same with scoops

Feb 06, 2008 | Malber WD1000 Front Load Washer/Dryer

1 Answer

Machine runs, but clothing won't dry


It sounds like your heating element is shot. The elements on this machine are very sensitive and if you use too much cleaning fluid the part will wear down after a while. You will need to get the part replaced (yuck) and start to use a little less washer fluid. Please let me know about your experience with the company (danfrogel@yahoo.com)

Sep 16, 2006 | Malber WD1000 Front Load Washer/Dryer

Not finding what you are looking for?

Open Questions:

See all Malber WD1000 Front Load Washer/Dryer Questions

Malber WD1000 Front Load Washer/Dryer Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Malber Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Jason Harris
Jason Harris

Level 2 Expert

272 Answers

Cindy Wells

Level 3 Expert

5645 Answers

Are you a Malber Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...