Question about Samsung Computers & Internet

1 Answer

SAMSUNG Altair-70 R1.04G Front panel connection?

Please give SAMSUNG Altair-70 R1.04G Front panel connection?

Posted by on

  • Nandika Sirinuwan
    Nandika Sirinuwan Jan 04, 2013

    I know different amoung MBs...but,I asked for SAMSUNG Altair-70 R1.04G front panel connection.which pis for power switch,power LED ...ect ?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Samsung Master
  • 2,226 Answers

Http://devxstuder.org/sam/samsung+altair+70+user+manual.html

Posted on May 25, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to calibrate the MSA Altair 4


Want to calibrate the MSA Altair 4 Gas Detector or MSA Altair 4X? Here's how:
1. Turn the MSA Altair 4 and MSA Altair 4X on in normal reading mode. Do this by pressing and holding the center button.
2. Once the MSA Altair 4 and MSA Altair 4X is in normal reading mode, you need to send it into calibration mode. Do this by pressing and holding right beeps at you and the screen asks you to zero the monitor (sensor refresh on the MSA Altair 4X).
3. Now that the screen is asking for confirmation, press the center button once to confirm. This will send the monitor into zeroing mode. Now is a good time to set the monitor down, and grab your calibration gas, regulator, and calibration adapter.
4. Open the valve on your regulator. This is a very important step so you do not ruin your calibration gas cylinder. Now screw it in to your calibration gas cylinder. Close the regulator once you hear gas spewing out of it. This is the signal to know your regulator is good to close. Continue screwing in the regulator until it stops. Do not overturn it.
5. Attach the tubing to the hose barb on your regulator. Make sure the tubing is also connected to your calibration adapter.
6. Wait for the screen to come up asking for you to apply calibration gas. Once this screen comes up, press the center button again to confirm. Screw the calibration adapter in to your gas detector. Once it is screwed on, turn on your gas.
7. Make sure your calibration gas values on the screen match what is on your calibration gas cylinder!
8. Once the calibration procedure is completed, turn your gas off and remove the calibration adapter from the MSA Altair 4 or MSA Altair 4X. The screen will go back to normal reading mode within a few seconds.
9. Congratulations! You have officially calibrated your MSA Altair 4 or MSA Altair 4X gas monitor. Make sure to record these readings in your calibration log!

If you come up with an error, the most likely bet is a bad oxygen sensor, but it could be a number of other issues. Feel free to email me.

on Sep 29, 2014 | MSA Altair 4 Multigas Detectors - 10085989

1 Answer

Altair 62 bios


http://sharedownloader.org/?q=samsung+altair+62+r1.01g+bios

Mar 12, 2014 | Computers & Internet

1 Answer

Where can i download the lan driver needed for altair-30 motherboard


http://www.computing.net/answers/drivers/looking-for-mother-board-driver-samsung-altair-30r104/10515.html

Dec 30, 2013 | Computers & Internet

1 Answer

A have an altair-30 v 1.04 motherboard need lan driver


you can go to samsung web site then to support then type in board at the search bar then download all updates while you are there to save you more time later ok.

Dec 30, 2013 | Samsung Computers & Internet

1 Answer

Sensor error comes up when turned on


Most likely this is a bad oxygen sensor. We have an informational page up at MSA Altair 4 Gas Detector which should help you find the correct parts. The oxygen sensor is here:

MSA Altair 4 Oxygen O2 Sensor

If there's anything we can help with, like walking you through calibration or how to install the sensor, please send me an email. james@idealcalibrations.com

Apr 12, 2013 | MSA Altair 4 Multigas Detectors - 10085989

1 Answer

Driver motherboard samsung altair 60 r1


https://vinafix.vn/threads/samsung-altair-60-r1-02g-dm-v55.9456/

Jun 14, 2012 | Samsung Computers & Internet

1 Answer

Can u give me the driver this spec... ALTAIR-70 R1


driver download
check before download. IT is that your notebook?
riderjunior_2.jpgRaTE mE

May 14, 2011 | Computers & Internet

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

3,180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Computers & Internet Experts

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

kakima

Level 3 Expert

102366 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Samsung Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...