Question about Salter Health & Beauty

Open Question

I receive an err display after replacing the battery on my salter 9140 scale

Upon replacing the correct battery (I checked!), I cannot get this scale to perform properly. It only gives me an 'ERR' display after tapping the scale to initiate its functioning.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Err 1 message on Taylor Lithium Elec Scale model 7346

This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck.

Thank you for your e-mail. The reboot below may clear the error from
your scale. You may need to do this several times to completely reboot
the system. Please let us know if you have any questions or continue to
display the Error.


1. Remove the battery from the scale
2. Set the scale on the floor without the battery in place.
3. Stand on the scale for 10 seconds (still without the battery)
4. Carefully replace the battery without turning the scale on.
5. Using only one foot, tap the scale or apply just enough pressure to
turn on the display. (It should show dashes or zero's) IMMEDIATELY
REMOVE YOUR FOOT.
6. Let the scale turn off
7. Step on the scale for a weight reading


Regards,


Linda DLT
Consumer Relations
Taylor Precision Products
& Salter Housewares
2220 Entrada del Sol, Suite A
Las Cruces, NM 88001
Toll free - 800-289-0944
866-843-3905
Direct - 575-526-0944 ext 3172

Posted on Jun 24, 2009

Ad
  • 1 Answer

SOURCE: HealthSmart bathroom scale displays "Err"

Put scale in round file can. Buy another cheap scale.

Posted on Oct 05, 2009

Testimonial: "The new scale works great and was on sale at Wal-mart for only $29."

  • 1 Answer

SOURCE: Reset digital bathroom scales

I cannot reset my digital scale to lbs. it is a conair ww body mass scale

Posted on Oct 18, 2009

  • 2 Answers

SOURCE: The display on my salter bathroom scales is

I held the two arrow and set buttons together for a few seconds and it cleared

Posted on Oct 20, 2009

  • 1 Answer

SOURCE: E appearing on display of Salter kitchen scale

i have the same problem- did you manage to fix it??

Posted on Dec 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Calibrate Salter model 9140 bathroom scales


Remove the battery and count to 10 and then replace it.

i found this
You do not reset the scale. It only saves the last recorded weight of the user. So, if you weighed yesterday, it will put your recorded weight in memory. The next time you select your user number and step on the scale, it will compute the difference from your previous record and save your current weight.

and also this

I had the same problem with my Salter 987 scale. Pull the battery out for about 10 seconds and put it back in. Then push the scale once so it turns on. After the blinking stops, push it once more. The scale will now zero itself. After the scale has zero'd itself it may turn off after a brief moment. It's now ready to use normally. If you're standing on the scale when it's trying to calibrate to zero, it will assume your weight is zero. Don't stand on the scale after replacing the battery until you first complete the steps listed above.

Not sure if this is the correct manual, but may be close. Page 3 and 4.

Salter Housewares Body Fat Computer Instruction Manual Page 3

Nov 27, 2017 | Salter Health & Beauty

1 Answer

After changing battery, why does err appear and not a 0?


The replacement battery could be defective or installed incorrectly.

Sep 05, 2015 | Salter 9037 - Digital Bathroom Scales /...

2 Answers

E appears on Salter scale, even with new batteries


Hallo I have problem witch kitchen scale Salter.E appear when I pushed on and it takes 3 sec

How can I fix this problem

Than You

Sep 18, 2009 | Salter 2001 electronic kitchen scale

1 Answer

I changed the battery on bathroom scale Salter 987


I had the same problem with my Salter 987 scale. Pull the battery out for about 10 seconds and put it back in. Then push the scale once so it turns on. After the blinking stops, push it once more. The scale will now zero itself. After the scale has zero'd itself it may turn off after a brief moment. It's now ready to use normally. If you're standing on the scale when it's trying to calibrate to zero, it will assume your weight is zero. Don't stand on the scale after replacing the battery untill you first complete the steps listed above.

Jul 21, 2009 | Salter Stainless Steel Electronic Bathroom...

1 Answer

E appearing on display of Salter kitchen scale


i have the same problem- did you manage to fix it??

Mar 31, 2009 | Salter 2001 electronic kitchen scale

4 Answers

Err 1 message on Taylor Lithium Elec Scale model 7346


This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck.

Thank you for your e-mail. The reboot below may clear the error from
your scale. You may need to do this several times to completely reboot
the system. Please let us know if you have any questions or continue to
display the Error.


1. Remove the battery from the scale
2. Set the scale on the floor without the battery in place.
3. Stand on the scale for 10 seconds (still without the battery)
4. Carefully replace the battery without turning the scale on.
5. Using only one foot, tap the scale or apply just enough pressure to
turn on the display. (It should show dashes or zero's) IMMEDIATELY
REMOVE YOUR FOOT.
6. Let the scale turn off
7. Step on the scale for a weight reading


Regards,


Linda DLT
Consumer Relations
Taylor Precision Products
& Salter Housewares
2220 Entrada del Sol, Suite A
Las Cruces, NM 88001
Toll free - 800-289-0944
866-843-3905
Direct - 575-526-0944 ext 3172

Feb 11, 2009 | Taylor & Digital Scale Lithium Scale

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Salter Health & Beauty Experts

traccie

Level 1 Expert

15 Answers

ray gallant

Level 3 Expert

46218 Answers

solver2010

Level 3 Expert

923 Answers

Are you a Salter Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...