I cant get the controls of the radio or clock to work at all. The radio comes on automatically when the car is started and the clock keeps time for a while, but then the radio goes off leaving the clock time standing still also? Its an LPG conversion - wondering if it cuts off as LPG kicks in? Please help?????
An expert who has achieved level 2 by getting 100 points
An expert that got 5 achievements.
An expert whose answer got voted for 20 times.
An expert that has 1 follower.
Re: Radio Goes Off after 5 - 10 mins
Oh no .your power supply problem.
first of all you have to check the power supply to the set is going off.check the fuse holder of car relating to the radio.then check the fuse holder closed to radio unit.some radios get own fuse in wire harness.then losse connection can be occur radio units socket.
if all are correct please observe power using multimeter whether its lose or going low level when you drive
if it is ok.
the power problem of your set.it can be bad contact of power button.faulty regulator .
also make shure the speaker wires are not damage.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
In order for Pandora to work you must have a Pandora account on your cell phone and have your phone linked to your radio via blu-tooth. Your radio access Pandora through your phone, the same is true with I-Heart Radio. If you have Panroda on your phone and the phone is turned on and in your car, it will automatically hook up when you go to Pandora on the radio, but only if you have already paired the phone to the Radio.
Below is the step-by-step procedure for setting the JVC clock. Please note that after you have entered the PSM mode, if you have not pressed a button for about 2 seconds, the radio will automatically exit the mode and return to normal operating mode. In that case, you must restart PSM by holding the "SEL" button until the display changes.
(1). Enter the PSM mode by pressing and holding the
SEL button until the display changes.
(2). Use the rocker switch left/right until "CLOCK
H" is displayed.
(3) Set the clock hours by turning the volume
(4) Press the rocker switch again until "CLOCK M"
(5) Set the clock minutes by turning the volume
(6) Press the SEL button to finish and EXIT.
1) Hold the source button until the radio shuts off. 2) Hold clock button until clock is displayed. 3) Use < and > buttons to move from hours to min. 4) Use volume up and down to adjust time. 5) Press band button when finished. 6) Press source button to turn radio on.
Setting Time 1 Press TITLE repeatedly until the time is displayed. For details, see “Displaying the Text” (page 13) 2 Press and hold TITLE for at least 2 seconds while the time is displayed. The time indication will blink. 3 Turn the Rotary encoder to adjust the hours while the time indication is blinking. 4 When the hour has been adjusted, press MODE. 5 Turn the Rotary encoder to adjust the minutes while the time indication is blinking. The time is automatically set 5 seconds after the minute adjustment. The time can also be manually set by pressing TITLE. • To synchronize the clock to another clock/watch or radio time announcement, press and hold MODE for at least 2 seconds after setting the “hour.” Minutes will reset to “00”. If the display shows over “30” minutes when you do this, the time will advance one hour. Listening to Radio 1 Press SOURCE/POWER until a radio frequency appears on the display. 2 Press BAND repeatedly until the desired radio band is displayed. F1 (FM1) F2 (FM2) AM F1 (FM1) 3 Press TUNE to select the tuning mode. DX SEEK (Distance mode) SEEK (Local mode) OFF (Manual mode) DX SEEK • The initial mode is Distance mode. Distance mode: Both strong and weak stations will be automatically tuned in (Automatic Seek Tuning). Local mode: Only strong stations will be automatically tuned in (Automatic Seek Tuning). Manual mode: The frequency is manually tuned in steps (Manual tuning). 4 Press or to tune in the desired station. Holding down or will change the frequency continuously. Manual Storing of Station Presets 1 Select the radio band and tune in a desired radio station you wish to store in the preset memory. 2 Press and hold, for at least 2 seconds, any one of the preset buttons (1 through 6) into which you wish to store the station. The selected station is stored. The display shows the band, preset number and station frequency memorized. •You will need to start from set up or you will not be able to set the mins
push and hold the clock button until the hrs flashes then use tuning button to change numbers or if your radio had 2 small pen tip buttons that read hrs & min pushing these with a pen tip will set the clock