Question about Behringer (UCG102) Sound Card

1 Answer

Guitar Link UCG-102 no sound

Hi bro i can get the amp combo 1 on screen i can turn the volume up on the metronome and volume on the noisegate but i cant get noise or volume from my guitar i have downloaded the amps and the driver do i need to download audiocity and kristylink to get sound from th amp because i cant find the on/off switch like all amps have every little hint will help i am itchin to get this going

Posted by on

  • nlpman Feb 03, 2009

    I've just got  ucg102 and NI comdos, audacity, and kristal and I can't get any sound. I also had driver problems with the one on the cd, so I've downloaded driver from net. Still no good. I am using vista hp on a mid range PC


    Any suggestions or ideas ?
    Dave

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

What you have to do is go into your speaker program or just right click the little speaker at the bottom of your screen and go to playback options and disable the headphone interface that comes with the Guitar Link,  after this happens it will put it back to your default speakers 
then click on the tab that says Recording options and turn up the volume on what should say Microphone USB Audio Codec

Afterwards go into your AC Box Combo program... hit "File" and than Audio+Midi Settings and At the top it should say "Interface" click on the box to the right of it and put it to your speaker program
Its decently complicated but it works PEACE

Posted on Mar 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant find or download volume icon(key) in lower right corner. windows help says there is no mixer? cant find mixer drivers?, only sound drivers. lost all settings and had to restore to 2009 settings! to...


EITHER YOUR SOUND DRIVER IS NOT INSTALLED OR WORING PROPERLY
OR THE SERVICE FOR SOUND HAS BEEN STOPPED.
KINDLY TRY THE FOLLOWING :

GOTO START -> RUN

TYPE SERVICES.MSC AND CLICK ON " OK "

ENABLE SOUND SERVICE FROM HERE AND RESTART THE COMPUTER.

THAT'S IT

PCCLINIC INDIA

Aug 10, 2011 | Compaq Audio Cards

2 Answers

My sound card is not working properly. and i cant play anythin.


hi.
What might be the problem is your sound driver what you need to do is download a new one or update the current one. Visit www.nodevice.com to download

Jul 07, 2011 | Creative Labs CT4870 / CT4780 Sound Card

1 Answer

No sound in my Toshiba laptop computer..but do get a loud noise when I turn up the volume...


Hello Sir, Hi, the loud noise means that the amplifier is working fine, the problem is the signal or the audio is missing. so check your cables (usually) or port connection (sometimes) and selector switch. update me of your progress.

Oct 17, 2010 | Emagic EMI 6|2m External Sound System

1 Answer

I can here myself speack like an echo?


Ugh, sounds like the card needs to be replaced or exchanged :(
But try this first: make sure the card is properly inserted into the slot. Also make sure it is in the correct slot. If there is more then one slot available try another one. Also try reinserting the card but do not force it.
Check all the contact points on the card
Most importantly make sure you are using the right software driver for the card and that it has been installed. Here is a link to a Driver Store
Also
Please be patient before your driver software will be downloaded. It's absolutely important to have a 181UR driver for your device. ...
www.driverstart.com/start316929.html

This should resolve the issue :)

Jul 24, 2010 | Dell 181UR Sound Card

1 Answer

Sound output is low nowadays even at full volume whereas before it was ok. I didn't change anything with my computer nor did I change my speakers.


Two possible causes.1) Vol Settings changed in windows2) Bad hardware
1) Check your system's sound settings:

For Xp
  • Goto Control Panel
  • Double Click Sound and Audio devices / Sound, Speech, and Audio Devices
  • In device Volume Click Advance
  • Master Volume Control Window will open
  • Increase all the volumes to max, also make sure that Mute us UNCHECKED.

OR
  • From the bottom right corner of your screen in system tray, double click a small speaker icon and open Master Volume Control.

For Vista and Windows 7
  • From system tray (its at bottom right corner of your screen) double click on small speaker icon, it will open Volume mixer
  • Increase the volume to max.

2) If this does not work, then test your speakers by connecting it to some other system and vice versa.
If you get desired sound volume when you connect some other speakers to your system, then you have to change your speakers. And if your speakers are working fine on other system then you may have to purchase a new sound card.

May 17, 2010 | Audio Cards

1 Answer

Sound system not working


try these steps --
1) click on the sound icon in the tray and make sure that its turned up and not muted.
2) got to start -> control panel -> sounds and audio devices -> audio
and under default device click volume and make sure that its turned up
3) click on volume and check the settings there
4) reinstall your audio driver. i dont have your system info so i cant point you to the download site, but if the first 3 steps dont work let me know and gimmie your info, make, model, sound card type (If ya know it) etc and i'll help you

Dec 25, 2008 | Audio Cards

2 Answers

Mbox 1 no ouput from protools


Double check and Ensure your headphones work.
Ensure that the master level is turned all the way to the right (Playback). I would also check that the main audio out of the Mbox is functioning so use two TRS 1/4" [balanced] cables to and amp and speakers to ensure master output jacks give you the same result. If they do chances are the Mbox is bad, if not it could be just the headphone preamp is bad

Nov 11, 2008 | Digidesign Mbox External Sound System

2 Answers

Phones 1-2 has both channels coming out of it


Had the same problem and fixed it today. It is the mute button. Whem you change from 1-2 to 3-4 if the mute button for 1-2 does not activate you will get the sound from 1-2 thru 3-4. Just change the setting and you are away. worked for me.

bruce

Jun 03, 2008 | Echo Indigo DJ Sound Card

1 Answer

US-144 noise


Hi

Usually Noise comes from distortion such as Electricity (50-60Hz), Main reason audio input cables might have shielding problem. Make sure cable is connected well and shield is not destroyed. You can understand it when you unplug the input connection and use the Computer volume by playing a digital media. If distortion persists contact to TASCAM @+1-323-727-7617

Good Luck

Jan 11, 2008 | Tascam US-144 Sound Card

Not finding what you are looking for?
Behringer (UCG102) Sound Card Logo

7,698 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Audio Cards Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mike

Level 3 Expert

4331 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Are you a Behringer Audio Card Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...