Question about Ryobi 18v One+ Circular Saw P501 18 Volt V 1 Plus

1 Answer

Oil vich oil i hevtu use

Posted by on

  • David Ford
    David Ford May 11, 2010

    oil for where, this tool has sealed bearings that do not reuire oil. Unless the header is not correct. Please furnish the correct model number and brand and I will check


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 90 Answers


Posted on Aug 04, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What type of oil does the saw require and how much?

Your Skil tool has been properly lubricated and
is ready to use. However it is recommended
that the gears be relubricated only with Skil
lubricants: No. 80111 (8 oz. tube), No. 80112
(pint) or No. 80113 (1/2 gal. can).
Always check the
oil level before
using the saw. To
check and add oil:
Remove plug from
power source and
place the saw's foot on a horizontal surface.
Remove oil plug using the same wrench used
to remove the saw blade. The oil level should
never be below bottom threads in the housing.
When adding oil, fill until oil starts to run out of
oil hole at arrow on housing and replace oil

part #80111 and is available from

Sep 27, 2012 | Skil MAG 77-75 7-1/4-Inch Magnesium Worm...

1 Answer

I have a Skilsaw wormdrive Mag 77 circular and the case on it says Oil is low what oil is best to use?

they make special "wormdrive" oil that is similar to gear lube but i has an additive for foaming. You should be able to go to any repair shop and buy a small bottle of the wormdrive oil. I would not recommend using anything else or you might damage the gears. Let me know if you need help finding the oil and if so give me your general location in the US and I will try and help you further.

Mar 31, 2011 | Saws

1 Answer

I need to know what kind of oil do I use to change the oil in my skill saw 77? Mine is pretty dirty, runs great but thought I should change the oil. Thanks Bill

Use Skil worm drive oil #80111 ($5-$6.00) at Home depot, or Bosch WD7LUB 2.3 FL. OZ. (I bought for $3.50 at Bosch service center.)

Aug 28, 2010 | Skil 7 1/4" Magnesium "Mag 77" Wormdrive...

1 Answer

For the Skil 77 worm drive circular saws what type of oil is required?

Use 90 weight gear/differential oil but if you use it outside in the cold weather it's too thick, use 40 weight oil then and switch to the 90 weight in the summer.

Jun 03, 2010 | Saws

1 Answer

Need to know what level oil in my skill saw mag77 should be?

have the saw as level as possible and put in oil until it starts to run out on the bottom of thread. Make sure you use a worm drive oil, just any oil will not work properly.

Mar 28, 2010 | Skil 7 1/4" Magnesium "Mag 77" Wormdrive...

1 Answer

I have a skil mag77 saw and need to replace the gear oil skil part # 80111 ive seen sugessted that i can use an anti foaming gear oil other than skil dist. where can i get some ,grainger/ autozone?...

Basically, anti-foam gear oil is regular oil without a detergent additive. I wouldn't play around and get any oil, since your mag77 is a nice piece of equiptment, but I understand that Skill will charge a premium for their oil. If I were you I'd spend the few extra bucks to be sure I have the correct oil.

Mar 08, 2010 | Skil 7 1/4" Magnesium "Mag 77" Wormdrive...

1 Answer

I am in Africa and the saw was shipped with little

drain out the remaining oil and if you can get just a clear mineral oil fine, otherwise standard gear oil would work also i.e. 80/90 weight

Nov 19, 2009 | Skil 7 1/4" Magnesium "Mag 77" Wormdrive...

1 Answer

How much/what type of oil goes in my old wormdrive saw?

their owners manual doesn't give an exact quantity however they say to unplug the tool first then remove the fill plug and the lower plug and the oil should run out past the first thread. they recommend using their oil 80111 8 oz. tube however any good worm drive lubricant will work, Don't use anything like gear lube because the worm drive lube has an additive for anto foaming. Let me know if you need more assistance

Nov 18, 2009 | Saws

1 Answer

Blown engine

makita likes you to use at least 91 octane fuel and a synthetic oil mixture. the stens oils is garbage, i switched to the makita oil around 6 months ago and i havent had a problem. also, the wacker saws use the same motor and their piston heads are sleeved in carbon so they last longer and dont score the cylinder as fast as the stock makita heads.

makita also makes a 100:1 mix hi performance oil you can use.

Oct 30, 2008 | Makita DPC8112 16" 81CC Gas Powered Power...

Not finding what you are looking for?
Ryobi 18v One+ Circular Saw P501 18 Volt V 1 Plus Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Saws Experts


Level 3 Expert

2396 Answers


Level 3 Expert

479 Answers

Jeff Harris

Level 2 Expert

81 Answers

Are you a Ryobi Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides