Question about Kenmore 24032\24036 Top Load Washer

1 Answer

Water runs into tub but does not fill?

Lthe water runs into tub but doesn;t fill to begin washing cycle? Every now and then the wash cycle will start and finsh other times it finishes the washing cycle but does the same thing during the rinse cycle. And there are times when it completely finishes a full cycle. start machine water runs it will not fill it just gose out the drain

Posted by on

  • Anonymous Mar 29, 2014

    water will not turn completely off after wash cycle is complete. small amount of water keeps running into drum from dispenser. I have to run a drain cycle to keep it from over flowing onto floor. If i do not keep eye on it constantly it will flood the laundry room.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

Be sure the drain hose is not lower than the wash tub this will caust the water to run out, 2nd be sure the drain hose is not pushed to far into the house stand pipe and the there is rome for air to go inbetween the drain hose and stand pipe eather of these will cause the machine to siphon mostly on rince cycle or on the 2nd and third loads you do. last your house drain could be starting to back up fill the washer with water and listen to it drain if you hear a gurggling sound in the house pipe you may need a plumber to cleanthis out for you.

Posted on Jan 20, 2009

  • Gerry Doucette
    Gerry Doucette Mar 27, 2014

    Tried all that mine is front loading

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Beko WMP652W washing machine will start cycle but get stuck at end of wash, doesnt go onto rinse or spin any help please?


see the next steps and use the common sense: God bless you
When the cycle doesn't advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.
8_2_2012_12_47_51_pm.gif

Aug 01, 2012 | Washing Machines

1 Answer

Kenmore 70 series wont stop filling with water to start the wash cycle


Lid off, right side circular pressure switch with black hose attached. Remove end of hose, blow down to make sure not blocked and blow into switch where hose attaches. Should click twice. If doesn't click, faulty pressure switch (replace)

May 19, 2012 | Washing Machines

1 Answer

Beginning of wash cycle starts agitating instead of filling w/water.


the water pressure/level switch contacts are welded together,usually the load selector switch for the amount of water lets it fill to a determined water level and the water level creates pressure in a tube from the tub to this switch and stops water fill and starts the wash agitation cycle,replace this switch inside the control panel

Mar 19, 2011 | Whirlpool Washing Machines

1 Answer

No water during any cycle.


if no water is coming in how is it agitating?is it filling at the beginning,then it starts to wash the clothes,now does it drain and then it won't fill again,send the model number and more info,

Jul 02, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Agitator starts at begining of cycle before washer is full


Please be carful as running the agitator without enough water will overheat and kick out the motor, however it should be ok when it resets itself.
Yes, the machine should stop agitating when you lift the lid so this too is part of the problem.
After looking at the print I can only suggest that the cam contacts in the timer ( contacts 12 and 14) that start the motor are burned and stuck together.
Quentin

Sep 17, 2009 | Frigidaire FEX831CS Top Load Stacked...

1 Answer

Frigidaire (LTF2940E) Washer starts, stops, starts, stops...


The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

May 07, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Water will not stay filled in tub on rinse cycle


It sounds like a siphon issue.
Check that the drain hose does a high loop before it goes into the drain pipe. (ie. drain hose loops above the water level inside the tub). Make sure the drain hose is not pushed too far down into the drain pipe. Also if the drain hose is sealed to the drain pipe this will create an airlock and a siphon will occur, allow air to enter between drain hose and drain pipe connection.
This should help you but if there is still a problem let me know and I'll try to assist you further.
Good luck!

Mar 21, 2009 | Maytag Washing Machines

1 Answer

Washing machine fills in the water but does not start the wash cycle


The fact that it does not fill completely can be related to a problem with the water-level switch, that regulates the water level.

See from Repairclinic:
"This switch is usually a diaphragm device with a small, clear tube attached between the switch and the bottom of the washer's outer tub. As the water level in the tub increases, the pressure on the air in the tube increases. When the pressure reaches a certain level, it activates the switch, shuts off the water, and signals the timer to begin the agitate cycle. If the switch is defective, it may prematurely signal the water to shut off. If so, you probably need to replace the water-level switch."

However, when it is only the switch the mashine usually completes the cycle, but with less water than normal.

A possibilty is that either the timer is faulty or there is a problem with the water supply.

Check that water is coming from water supply with regular pressure, and that hoses back there are not obstructed.

More likely you will have to replace the timer.

See again from Repairclinic:
"When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water."

  • You can find parts at the following websites, you need to input your model number. If the part is not listed contact them.

    Repairclinic

    Partselect

    Don't forget to rate the solution.

    Many thanks.

    Sep 01, 2008 | Washing Machines

    Not finding what you are looking for?
    Kenmore 24032\24036 Top Load Washer Logo

    986 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kenmore Washing Machines Experts

    Richard Roth
    Richard Roth

    Level 3 Expert

    9472 Answers

    Jesus  Colon
    Jesus Colon

    Level 1 Expert

    12 Answers

    Fred Sops

    Level 2 Expert

    271 Answers

    Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...