Question about Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103

Open Question

Kenmore dishwasher - control panel not working

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: kenmore elite dishwasher stopped in middle of cycle

My Smeg (never buying brand again) dishwasher UKSTX1 has error message e9 not covered in manual

Posted on Jan 26, 2009

Ad
aborcass
  • 2651 Answers

SOURCE: Kenmore dishwasher control panel cracked

unfortunatly youll need to replace the entire control panel, it does not come as a separate mylar overlay,

Posted on Mar 17, 2009

SOURCE: kenmore dishwasher 13749 needs a new electronic control panel

I have a similar problem. The control panel buttons are peeling off. It seems like a manufacturing defect rather htan steam damage. Did you replace the panel?
Thank you. Michele.

Posted on Oct 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Dishwasher 665.15699k210 The dishwasher has been reset and wont work.


Hello Lindsey!

Here is the link to the "troubleshooting" part of the manual for Kenmore Dishwasher. I hope it will help :) http://manualsbrain.com/en/manuals/960623/?page=16

Jul 27, 2017 | The Computers & Internet

1 Answer

Kid 60 s10 please give fault codes


Hi Roger, Hope this helps......CHEERS..

KENMORE DISHWASHER ERROR CODES

Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

Mar 31, 2016 | Kenmore Dishwashers

1 Answer

Kenmore dishwasher blinking E2F2


Unlock your Kenmore dishwasher control panel by pressing and holding the "Heated Dry" button for four seconds.

Press a series of four buttons in quick succession. Press "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" to instruct your Kenmore dishwasher to run a short diagnostic test.

Then you have to wait 2 minutes while your Kenmore dishwasher runs its diagnostic test.

Then press the "Cancel/Drain" button once your dishwasher has completed its diagnostic test. This should reset your dishwasher control panel and stop any lights from blinking.




Jan 29, 2015 | Kenmore Dishwashers

1 Answer

Refresh control panel


Instructions
    • 1

      Unlock your Kenmore dishwasher control panel by pressing and holding the "Heated Dry" button for four seconds.

    • 2

      Press a series of four buttons in quick succession. Press "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" to instruct your Kenmore dishwasher to run a short diagnostic test.

    • 3

      Wait for two minutes while your Kenmore dishwasher runs its diagnostic test.

    • 4

      Press the "Cancel/Drain" button once your dishwasher has completed its diagnostic test. This should reset your dishwasher control panel and stop the "Clean" light from blinking repeatedly.

      Hope this will be of help to you

      Have an awesome day



Feb 08, 2012 | Kenmore Dishwashers

1 Answer

Error 1 on kenwood dishwasher


Hello.
Manufactured by Whirlpool, Kenmore dishwashers have an electronic control panel that must be unlocked in order to set or make changes to your dishwashing cycle. If an error light is blinking on your dishwasher's control panel, the panel must be reset before you can gain access. Blinking lights on your dishwasher control panel may signal a mechanical problem that needs to be repaired. If the lights continue to blink after you've reset the control panel, contact Sears to service your Kenmore dishwasher or consider troubleshooting the appliance yourself.
1Press and hold the "Heated Dry" button on your Kenmore dishwasher for four seconds to unlock the dishwasher control panel.
2 Press the "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" buttons one after the other, in fairly quick succession.
3 Wait for the dishwasher to run a short diagnostic test.
4 Press the "Cancel/Drain" button at the end of the diagnostic test cycle. This should reset the control panel on your Kenmore dishwasher.

Thanks.

Nov 05, 2011 | Kenwood KDW243A Builtin Dishwasher

1 Answer

My quiet partner 111 whirlpool dishwasher is flashing clean


Hello.
Manufactured by Whirlpool, Kenmore dishwashers have an electronic control panel that must be unlocked in order to set or make changes to your dishwashing cycle. If an error light is blinking on your dishwasher's control panel, the panel must be reset before you can gain access. Blinking lights on your dishwasher control panel may signal a mechanical problem that needs to be repaired. If the lights continue to blink after you've reset the control panel, contact Sears to service your Kenmore dishwasher or consider troubleshooting the appliance yourself.
1Press and hold the "Heated Dry" button on your Kenmore dishwasher for four seconds to unlock the dishwasher control panel.
2 Press the "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" buttons one after the other, in fairly quick succession.
3 Wait for the dishwasher to run a short diagnostic test.
4 Press the "Cancel/Drain" button at the end of the diagnostic test cycle. This should reset the control panel on your Kenmore dishwasher.

Thanks.

Nov 04, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Dishwasher kenmore


ok this may sound stupid but make sure the power to the dishwasher is on. also I usually find a switch on a wall that shuts the dishwasher on/off is usually off.

Sep 05, 2009 | Kenmore Refrigerators

1 Answer

Kenmore dishwasher control panel cracked


unfortunatly youll need to replace the entire control panel, it does not come as a separate mylar overlay,

Mar 17, 2009 | Kenmore Dishwashers

1 Answer

Dishwasher "lock on ' control wont turn off


Hold the control lock in for more than four seconds. See if that works.

Jul 25, 2007 | Kenmore 15762 Dishwasher

Not finding what you are looking for?
Kenmore Elite Stainless Steel 24" BuiltIn Dishwasher with TurboZone Rotating Spray Jets 13103 Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

D. E. Hev

Level 3 Expert

1173 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...