Question about Canon Pixma MG5220 InkJet Printer

Open Question

How can I replace the ink absorber for canon pixma MG5220

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: how to replace or clean waste ink absorber in Canon PIXMA iP3000

Cleaning or replacing the ink absorber is not for the faint of heart, it's a messy job,wear rubber gloves and old clothes. After the cleaning you still have to reset the counter so it will let you print again, so don't forget that part.
Here is a link to a web page with the full instructions for both procedures.

http://www.polyphoto.com/tutorials/PrintHeadCleaning/CanonCleaningAndReset.html

Posted on Jan 08, 2009

  • 1 Answer

SOURCE: Waste Ink Absorber is full In Canon Pixma IP3300

my printer say, "the ink absorber is full".

Posted on Dec 06, 2008

  • 83 Answers

SOURCE: Ink waste absorber is full. Canon IP2000. How do I repair it?

Well, at some point you will need to either replace or wash the absorber pads in the printer - but you can reset the warning as follows:

1) Turn the printer off
2) Press and hold the <resume>button
3) Press and hold the <power> button
4) While holding down <power> release <resume>
5) With the power button still held down, press <resume> twice more
6) Release the power button
7) Press and release the <resume> button 4 times
8) Press and release the <power> button twice

At this point, the printer should come back online with the waste ink warning reset

Personally, I would only do this once before actually changing the ink absorber pad...

Posted on Aug 31, 2009

  • 5603 Answers

SOURCE: Ink absorber

A special service software program is needed to reset the internal counter for the ink absorber.

Check here:

http://www.pdfoo.com/result-service-tool-software-resetter-for-canon-pixma-ix-5000.html

Posted on Sep 01, 2009

xptareq2000
  • 1447 Answers

SOURCE: canon pixma mp160 ink absorber is full

e75ff09.jpg this the reset wast ink please follow it step by step

Posted on Sep 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the ink cartridge for my canon mg5220


Yes, you will get that message. You may be able to buy a "chip resetter" for your carts. I've had good experience with this supplier of resetters, refillable carts and refill ink:

Sep 12, 2014 | Canon Pixma Mg5220 Wireless All-in-one...

1 Answer

How do I remover a paper jam under ink cartridges in Prima Canon MG5220


rEMOVE THE INK CARTRIDGES AND REMOVE THE CARTRIDGE BASE SUPPORT.

Mar 20, 2013 | Canon Pixma MG5220 InkJet Printer

1 Answer

Every time I try to print my canon pixma MG5220 says 'printer error 6C10'


You need replace the ink absorber .
Or you can disassembly the printer and clean with running water tha ink abserber.
Is located below the cartrigde

Is important for people who share their knowledge, know your comments.
If the answer is helpful, rate my answers

Sep 27, 2011 | Canon Pixma MG5220 InkJet Printer

2 Answers

The color ink cartridge that is " blinking " is


Don't buy Canon as they absolutely ROB you for the ink!! They are worse than ****** dealers! At least HP allows you to use non (rip-off) OEM cartridges without all the hassle! My printer will be thrown out after the ink runs out as I will not be ripped-off by Canon again!

Apr 30, 2011 | Canon Pixma MG5220 InkJet Printer

1 Answer

How to take apart Cannon PIXMA iP3000 to clean the waste absorber


You need to replace the ink absorber kit and to completely disassemble the printer to replace the absorber. Attempting to clean the ink absorber is not recommended. Self servicing the absorber can be a very messy operation. I would check with a Canon repair center to see what the cost to have the servicing done by a trained technician. In some cases, it is cheaper to replace the printer.

May 22, 2010 | Canon PIXMA iP3000 InkJet Photo Printer

2 Answers

Ink absorber full


This is a very common problems with canon printers. They are set for a certain number of prints and they need the ink absorber serviced. Now along with resetting the printer its best to replace the absorber. Here is link to site that has reset instructions.
http://ij-forum.blogspot.com/2008/08/reset-waste-ink-absorber-error-waste.html
Thanks,
Lee

Nov 05, 2009 | Canon PIXMA iP3300 InkJet Photo Printer

1 Answer

Ink absorber


A special service software program is needed to reset the internal counter for the ink absorber.

Check here:

http://www.pdfoo.com/result-service-tool-software-resetter-for-canon-pixma-ix-5000.html

Sep 01, 2009 | Canon Office Equipment & Supplies

2 Answers

What does ink absorber full mean on Canon Pixma 1700?


my Canon pixma keeps coming up ink absorber full cannot print

Oct 30, 2008 | Canon PIXMA iP1600 Printer

Not finding what you are looking for?
Canon Pixma MG5220 InkJet Printer Logo

Related Topics:

937 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1924 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...