Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

F2 error I have rec'd the f2 error. I have completely cleaned the exterior drain line, but I continually get the f2 error and only the drain/spin or the rinse/spin cycle works to resolve this. Help. Ready to call a repair man

Posted by on

  • Anonymous Jan 19, 2009

    dito! to grabycrews problem

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

F2 means the unit is draining to slow...you need to clean your pump filter...if you need help with that post to onthejob

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Kenmore HE3t washer than continues to stop during the cycle and flash the F2 error code even after cleaning out lines, hoses, trap, boot and replacing the drain pump.


It is possible that the brushes on the motor that spins the drum are worn down. The drum will start and stop when this happens. Check the brushes.

Nov 07, 2013 | Kenmore Washing Machines

1 Answer

Before it starts spinning F2 comes up what does that mean?


Hello & Welcome to FixYa

F2 is a drain error in your washer, if the unit is unable to drain then after 4 minutes it will display suds and then F2. The first thing that should be done is cleaning the drain hose and the drain pump filter, you can take out three torx screws from the bottom front panel and then clean the area completely, lift up the cap to clean the filter. If the error returns then check the drain pump if it is not working then replacing the pump is recommended repair. Please get back to me if you have any other questions.

Kevin

Jul 06, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

My Duet front loader.. once it starts washing it stops and an error f2 code comes up and it will not complete the washer the clothes are left wet. if i move to spin only it still wont same code comes up


Hello & Welcome to FixYa

F2 is a drain error in your washer, if the unit is unable to drain then after 4 minutes it will display suds and then F2. The first thing that should be done is cleaning the drain hose and the drain pump filter, you can take out three torx screws from the bottom front panel and then clean the area completely, lift up the cap to clean the filter. If the error returns then check the drain pump if it is not working then replacing the pump is recommended repair. Please get back to me if you have any other questions.

Kevin

Jun 14, 2011 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

F2 Shows up on control screen and cloths dont go throw spin cycle.


Hello & Welcome to FixYa

F2 is a drain error in your Kenmore washer, if the unit is unable to drain then after 4 minutes it will display sud and then F2. The first thing that should be done is cleaning the drain hose and the drain pump filter, you can take out three torx screws from the bottom front panel and then clean the area completely, lift up the cap to clean the filter. If the error returns then check the drain pump if it is not working then replacing the pump is recommended repair. Please get back to me if you have any other questions.

Kevin

Feb 15, 2011 | Whirlpool GHW9400 Front Load Washer

1 Answer

Kenmore Elite Oasis HE washer error code F2


The error code must be cleared first to make the machine back into operation. You have to press the PAUSE/CANCEL button twice to clear the error on the display.

The only filter the machine has is the one you removed to clean the pump. When the error is cleared, you can check the pump whether it is operating properly or not by running the diagnostic test.

Diagnostic Test Mode Procedure

  1. Close the door.
  2. Select the DRAIN/SPIN.
  3. Select NO SPIN by pressing the SPIN SELECT button.
  4. Press RINSE/HOLD or PREWASH OPTION button four times within five seconds.
  5. "C:00" will show on the display indicating that the door is locked and the diagnostic test starts.
  6. Press the button you pressed in step 4 above two times. "C:01" will show on the display and the machine starts to fill.
  7. Press PAUSE/CANCEL button two times when there's enough water inside the tub to stop the test.
  8. Observe the water level falls as the pump starts draining the water. Replace the pump if the water inside the tub does not drain. You have removed and cleaned the pump so you can easily replace it too.
Please inform me about the result of the diagnostic test and if you still need any assistance regarding this problem.

Jan 20, 2010 | Washing Machines

1 Answer

My duet whirlpool stops at the rinse or spin cyle and gives error code F02. I cleaned out the drain pump strainer twice and got much out of it. It still errors. I took th epum completely apart last...


"F02" is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a "SUDS" error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:

1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.

To check the drain pump, click on the following link for step-by-step instructions.


http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front

If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Jan 04, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Washer will not advance in the rinse cycle,water just runs continuely.


check the drain hose it should be only 6 to 8 inch in your drain line if drain hose is all the way in the drain line correct it and you will be fine.

May 21, 2009 | Washing Machines

1 Answer

Takes almost 2 hours to complete a wash cycle


Have you ever cleaned it out? Its likely due to a plugged drain, not allowing the system to drain fast enough for the normal cycle. Check out my solution on
http://www.fixya.com/support/t114322-kenmore_elite_h3t_washer

-Todd

Mar 30, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

2 Answers

Does not drain error code f2


There is a block in your pump, you have to locate it, dismantle it & remove the block. Plug off the wall first.

Mar 13, 2009 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

543 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...