Question about Washing Machines

1 Answer

AEG Lavamat 74689 Update wont pump out

The washing cycle works perfectly until it reaches the rinse program then it won't click on to pump. I have cleaned drain hose and tried to turn dial to pump but just keeps washing. Drained machine manually. It will work on spin once empty but just no attempt to pump or rinse.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Washing Mach... Master
  • 17,129 Answers

Possible that the program timer is faulty as it fails to switch on the pump in the required sequence. You can clean the contacts, check the power to the pump, trace the pump power line to the timer which can confirm the case. In such cases the timer must be replaced.

Posted on Jan 02, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: LG wft7014pp wont drain rinse nor spin

do you have a drip-dry function...as this cancels the spin cycle unless you select it yourself

Posted on Jan 03, 2008

  • 1 Answer

SOURCE: LG WD-8013F wont spin

Hi deppgirl,
I checked the lint filter at the front bottom left hand side and it was full of junk.  Once emptied it worked a treat.  Pull the flap down and turn the large knob anti-clockwise and pull to remove.  Good luck.

Posted on Apr 22, 2008

  • 1 Answer

SOURCE: Whirlpool 6th sense awm8163 programes never stops now cannot get it to work at all

The pump is at the lower left of the front of the machine covered by a white plate. Use a bowl to catch any remaining water when opening the screw thread inside and then clean and replace. If it is truely beyond repair then a new filter pump can be bought from ebay for £3 or thereabouts.

I have just drained mine manually in this way and am going to run it empty with soda crystals to glean a few more days use whilst the new pump arrives.

Good luck :)

Posted on May 07, 2008

  • 1 Answer

SOURCE: aeg 76669 oko lavamat machine not


I have had the same problem. If you switch the machine to off and then to cotton/linen 95, then press at the same time prewash, soaking, qick wash and stain buttons for 10 seconds switch it off. When I switched it on it worked.

Posted on Jun 24, 2008

  • 1 Answer

SOURCE: Washing machine will not drain

I have a maytag washer that when it fills with water it wont drain out..the spin cycle just makes a noise and it wont do anything..any ideas what i can do to fix it thanks

Posted on Nov 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AEG Lavamat 64809 error code E30


Lavamat?! Where in the *&%^ is this machine from? Yugoslavia! I'm guessing it will not allow water IN Because only the Spin (Centrifuge) cycle works?! So if that is so you need your water inlet valves replaced, there are Two. Even in machines named after a Bar of Soap!

Jan 04, 2014 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

No water


It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve:
http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Jan 14, 2013 | AEG Lavamat 72640 Front Load Washer

1 Answer

Aeg lavamat 54600 won't begin cycle


check your pump down at the bottom of the machine take the bottom plinth off the plastic that runs along the bottom of the machine once off you will see your pump undo the plastic screw and get your self a towel and a small and big bowl there will be a lot of water so when you have took the screw out start turning the pump cap very slowly and when you have filled the small bowl close it and keep repeating it till all water is gone then take it right out if its stuck then pull it clean it out and put back together don't for get to turn your machine off be for doing any thing ok hope i have helped if after you have done the pump and the machine still do the same thing then its programmer ok

Nov 02, 2012 | AEG Washing Machines

1 Answer

Hi my AEG OKO-LAVAMAT 88830 is about 10n years old. Today I was cleaning my machine. I filled the machine up with water on the rinse cycle then turned it to pump. I did this a few times as I have had a...


Hi from retired Englishman in SW France,

According to my list for AEG Lavamat washers, 'C3' stands for 3 possible causes 1 'safety flood device operated' (I suspect it means that it has sensed some water in the bottom tray. Not an easy job to do but I would check for a leak underneath), 2 'pump fault' and 3 'module fault'. Sorry I can not be of more help ;-0(

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Sep 04, 2011 | AEG Lavamat 88840 Front Load Washer

1 Answer

My AEG Lavamat 62810 keeps coming up with an error code E60. What is this?


On my AEG Lavamat 62810, when I turn on a wash cycle a motor (pump?) runs for 10–20 seconds then the machine switches off, with no error message. When this happened a few weeks agao running a drain cycle seemed to cure it; now the same thing happens on spin/drain/rinse cycles too. Any ideas?

Aug 06, 2010 | AEG Washing Machines

1 Answer

AEG Lavamat 76400 during spin cycle blows a fuse


its not the heat element its the water pump i would say it has gone to ground try disconnecting the water pump if the fuse does not trip then replace the water pump

Jul 03, 2010 | Washing Machines

2 Answers

AEG 72640 stopping mid-cycle no error code showing


I have the same problem with my Oko Lavamat 74639 Update. I've tried changing the vacuum sensor, but no luck.
Did you get your fixed?
Olafur

Oct 19, 2009 | AEG Lavamat 72640 Front Load Washer

1 Answer

AEG lavamat 6955 sensorlogic, was showing F2,nowF3


Waited half hour; on start up F3 had cleared..pump overheat? Suspect sticky pump bearing..new pump.

Jun 10, 2009 | AEG Lavamat 88840 Front Load Washer

1 Answer

AEG 72640 update


e20 means cant drain i usually found itsufficient to clean filter and restart but this time i blew down waste pipe /drain,cancelled program and reset

Jan 13, 2008 | AEG Lavamat 72640 Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Brad Brown

Level 3 Expert

15639 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...