Question about Pioneer PRO-530HD 53" Rear Projection Television

1 Answer

Pioneer elite pro-530hd tv---no picture at all!

I have a pioneer elite pro-530hd tv. will not turn on at all. no picture.
any suggestions? it is worth trying to fix? thanks, any advice would be appreciated.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 532nd 53 that shuts off and red stand by lite comes on in the back. If you wait awhile and unplug it and plug it back in it will come on again and then shut off after an hour or two

Posted on Oct 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEED OPERATING MANUAL FOR PIONEER ELITE PRO 530 HD TV


both may be a little hard to find anymore, the main problem is dead set and that is bad soldering all over the giant power supply board this set uses.

Sep 02, 2012 | Pioneer PRO-530HD 53" Rear Projection...

1 Answer

What's your problem?Pioneer PRO-530HD 53 in. Rear Projection Television flashing red standby light


This and a few other models like it have one real common issue:

they develop from age and heat bad solder connections all over the power board (rather large board).

My experience with them is the fix usually is remove rear cover and follow power cord to power board (a lot of plugs to mark) and remove that board----then solder every single connection on the board which by the way has some special fuses on it.

Jun 14, 2012 | Pioneer PRO-530HD 53" Rear Projection...

1 Answer

I have multiple colors on the screen of my 530hd pioneer elite TV when it warms up. When I try to adjust the convergence I am unable to move the red line far enough to converge on the blue or green line.


The convergence of your tv is defective try to replace it. You will find the convergence chip inside your tv, try to open the back cover of your tv but be sure to unplug the tv first. Try to look the large aluminum plate it is the heat sink, your convergence chip is attached to that heat sink it has a marking of stk-*** followed by a number you should remove it from the pcb using a soldering iron, and soldering pump but be very careful you might damage the pcb and may caused another fault to your unit. Or you can contact a service technician to save you from stress. Good day and best regards.

Jul 19, 2011 | Pioneer PRO-530HD 53" Rear Projection...

2 Answers

Pioneer Elite Pro-118 rear projection tv


ya mine did something close to the same. at the moment i covered the blue canon inside the tv now the picture isnt 2 of eveything. the tv comes apart easy from the front good luck mike

May 02, 2010 | Pioneer PRO-200 60" Rear Projection...

1 Answer

Pioneer Elite Pro 620 HD TV on several occasions the screen has gone black but sound continues and the power green libht remains on. After shutting down for 10-15 minutes picture comes back.


Pioneer Elite Pro rear projection 620HD - Picture is still there but brightness and "white" have faded over years allowing for mediocre viewing when room is dark only. During the daylight picture is visible if viewed straight on and within 15 feet from set. Any suggestions?

Oct 16, 2009 | Projection Televisions

1 Answer

Pioneer elite pro 118


if the tv is more than 10 years old no its not worth replacing the power supply.if its 5 years or newer yes it owuld be worth the money

Jul 17, 2008 | Pioneer PRO-200 60" Rear Projection...

1 Answer

Problem with pioneer elite pro-99


We are having the same problem of the Pioneer Elite Pro-99 turning itself off all of a sudden. The red 'non' power button comes on as if we had turned it off remotely.
We would love to resolve this. If you can help let us know.

Jun 30, 2008 | Pioneer PRO-99 TV

1 Answer

Power problems with PRO-530HD


need stk392-110 if that in it but i use stk392-120 you whant to ch restor by the ic stk392-110

Mar 30, 2008 | Pioneer PRO-530HDi 53" Rear Projection...

2 Answers

Pioneer PRO-510HD Elite


since your tv is 6yrs old it could be that the video circuit has cold solder that needs to be resolder if that does not work then a focus on the video circuit by replacing the component there, it could be an ic or transistors or diode.if you are not a tech get one to look at your set.good luck.for further help email me at nicodhem@yahoo.com

Apr 06, 2007 | Pioneer PRO-510HD 53" Rear Projection...

Not finding what you are looking for?
Pioneer PRO-530HD 53" Rear Projection Television Logo

Related Topics:

665 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

zorbrack

Level 1 Expert

19 Answers

Are you a Pioneer Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...