Question about Whirlpool Pearl Ballade True Bathtub with Back Massage - 100463-100

1 Answer

Broken back massage jet unable to purchase locally

Just the part that actually screws into the jet any help appreciated

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 68 Answers

Hi robrezza,

Here's the number the Pearl/maax Plant.
For maintenance, installation or general technical queries about your MAAX products, we encourage you to contact us at: Tel.: 1-888-957-7816 option # 2 Fax: 1-800-201-8308 (418) 387-9086

Have your tub model when you call. They usually are pretty helpful. Sometimes it goes to voice mail for the tech person but they call back after a bit

Please rate this response and Good Luck, Phil

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Housing for jet is broken on spurlin tub


You can probably get one at your local pool and spa supply. If you do not have an acess door or access panells to that side of the tub, then you may have to take the tub out of its frame. You will first have to TURN OFF ANY POWER SUPPLY to the pump and any other device such as an optional heater etc. Then turn the water supply valves off and disconnect them where they exit the valve.Disconnect the drain by unscrewing the inner drain strainer where the water runs out of the tub and the screws from the trip lever (that works the stopper) and pull it completely out. Remove any caulking around the tubs rim and lift the tub from its frame. Make repairs and replace in this same order.

Jun 11, 2012 | Bathtubs & Whirlpools

2 Answers

One of the jet assemblies on my Jacuzzi 325 hot tub popped out and I can't get it to stay back in. i've been pushing it in as hard as I can but when I turn the pumps on it pops back out. Should I be...


once a jet face has fallen out of a hot tub that means the insert has failed and is broken. you will need to locate a new jet insert. Jet inserts have little tabs on them that hold them in place and when they get worn out the jet face will fall out into the tub.

Jan 29, 2011 | Jacuzzi Bathtubs & Whirlpools

1 Answer

How are you?


I like it's designing.A whirlpool tub provides a deep tissuemassage. Water is pulled from the bath, passes through the pipes, and back outthrough a jet - providing a massage to the areas in front of the jets.Whirlpools provide the most vigorous form of massage. They can be combined withan in-line heater that will maintain the temperature of water within a fewdegrees of what it was poured at for as long as the whirlpool is running. Inorder to get a good reputation now they are made from quality acrylic, heavy duty fiberglassbacking, quality motors and jets. In the past they had a bad image.They recoveredfrom that by using good materials for manufacturing.

Nov 30, 2010 | Bathtubs & Whirlpools

2 Answers

I have a leaking jet in a pearl jet tub. it's an older model with just two jets installed in 1997 the jet leaks and i don't know how to jet the face plate off the jet, or have a diagram as to get the jet...


If there is a  threaded nut on the back of the jet, undo the nut as much as possible and push the jet out into the tub. Spread aquarium grade silicone around the jet and push back into the hole, put more silicone in front of the nut, you may have to spread it in the small area with your finger or if you can squirt it in from the tube of silicone. If there is no  threaded ring on the backside of the jet, go to the jet in the tub and looking down on the jet, turn it to the right. It should pop and pull out of the housing. There will be a retaining ring that may require a special tool to remove it, once the ring is out, clean it very well, spread silicon on the threads and the lip. Reinstall in the hole, reinstall jet wait 24 hours and fill and test for leaks. Take you time and you will not have to do it over again. Check where the leak is coming from, sometimes there is a hairline crack in the jet assembly, if this is the case, make sure the area is dry then use a 2 part epoxy for plastic (from lowes or home depot) and smear this all over and around the crack, let dry 24 hours, fill and test.

Sep 28, 2009 | Whirlpool Pearl Ballade True Bathtub with...

1 Answer

Stale water odour when jets havent been used on massage type spa


There are several cleaning methods on the internet. I would contact the maker of the tub and see if they have a cleaning agent. I know that Jacuzzi and Aquatic industries have a cleaner that works rather well. I have seen one on the net that uses 2 teaspoons of powder dishwasher soap mixed with bleach. I have not tried this one so don't know how well it works. The ones from the tub companies are not cheap, but if you want something that is going to do the job, spend the money.

Sep 28, 2009 | Hampton Technologies Hampton R -...

1 Answer

Need to know how to access the motor on my whirlpool tub


Yes you should have an access panel to the pump somewhere. It sounds like you have already found it. You may want to get a qualified electrician involved. There are at least three sources of possible failure. The first and least expensive is that the motor tripped the ground fault interrupter and just needs to be reset. The second is that the switch has gone bad. The third and most expensive is that the pump is broken and needs to be replaced.

Feb 28, 2009 | Whirlpool Pearl AIGO True Bathtub with...

1 Answer

What products to us in my jet bath


Bubble bath is definitely out of the question. Provide any of the products that you are using do not have a detergent base or bubbles so to speak, you can use them. Depending on how many times a week you use it you might want to get a cleaner that they use on hot tubs from you local pool distributer. I hope this helps you.

Nov 26, 2008 | Whirlpool Pearl Navarre 7242 True Bathtub...

Not finding what you are looking for?
Whirlpool Pearl Ballade True  Bathtub with Back Massage - 100463-100 Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bathtubs & Whirlpools Experts

rjbeg123

Level 3 Expert

272 Answers

john h

Level 3 Expert

7167 Answers

Mike

Level 3 Expert

4331 Answers

Are you a Bathtub and Whirlpool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...