Question about Kenwood KW85 Air Conditioner

2 Answers

E1 fault on kenwood dishwasher kdw243a

E1 fault showing on kenwood dishwasher kdw243a
Should supply booklet on all these faults Unable to use appliance

Posted by on

  • ircia Jan 18, 2009

    post a solution and is there a booklet available?

  • Anonymous May 06, 2009

    same fault on mine E1 but don't know what it means do I have to get a man out to sort it ! (kenwood dishwasher kwd243a)

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Error code E1 refers to "lack of water inlet pressure" the valve the elctrically lets in the water might be at fault

Posted on Jul 14, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sorry was asking about kenwood kdw243a e1 fault can you help me ?

Posted on Jan 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code E1 and E4


PDF]SERVICE Manual - Quietside

https://www.quietside.com/archives/.../Service%20ACC1800C.pdf
When error occurs in air conditioner, error code is displayed on indoor unit .... Display priority order at overlapping error : E1?E4?E5?P0?P0?P5?P6?t1? ...

Midea air conditioner error codes

airmaster.net/midea-air-conditioner-error-codes/
Midea air conditioner error codes. Indoor unit error code explanation: R series: ... E1, Indoor / outdoor units communication protection. E2, Zero-crossing signal error ... E4, Outdoor unit temp. sensor or connector of temp. sensor is defective.

[PDF]Download the Fault Error Code Booklet - Samsung


Dec 05, 2015 | Air Conditioners

3 Answers

Fault E3 Have same problem, fan works fine but will not turn on cold air. Display shows "e3". I have a remote, but do not see a button "c".


Try this : Start the unit using the remote control, after that push the C button of remote control if C display at the unit then off the unit and plug out the power supply. Then plug in again and "on" the unit using the remote control.

Aug 09, 2008 | Kenwood KW85 Air Conditioner

2 Answers

Greeting, I have problem with SAMSUNG air condicioner inverter. The display shows me an error E1 A1 and does not include the external unit, please help what is the problem.


E-1 Room sensor and A1 Indoor PCB fault. Please you replace first,indoor sensor and reset.Sometimes indoor pcb shows fault code due to sensor short. After replacing sensor it will show only A! or sometimes no error. If it shows A1, you have to repair/replace PCB. Helpful?

Jan 24, 2011 | Samsung AW1203B Air Conditioner

2 Answers

Error code E2 A.C. AUX


Disply E2 error Coming

Jul 23, 2010 | Air Conditioners

1 Answer

Hi my kenwood dishwasher kdw243a is not releasing the tablet door and not getting hot ?


It sounds as though the heater has failed. I would expect an error code such as e3 to be displayed. It should be possible to test the heater element with a multimeter set on ohms.

Nov 30, 2009 | Kenwood KW85 Air Conditioner

1 Answer

Moved into new house need set of instructions


Try this. I'm not sure if it applies to your model.

The reset sequence used is:
1) Crack the door open.
2) Within 3 seconds press the following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry
3) Close and latch the door
4) Press the cancel button (the circle with the triangle in it)

Jan 19, 2009 | Kenwood KW85 Air Conditioner

1 Answer

Fitting a door to Kenwood dishwasher KDW243A


Hello, Found this while looking for the answer myself. The vanity door fell off last night onto my foot and so needs must as it really hurt!

Anyway there are 2 top pillars that fit into the upper appliance door. Then there are two plates that need to set to finished height.

To fit. First insert the top pillars into the large openings. Now open the dishwasher door a bit, took two of us to get this right, and push the vanity door as high up as you can. Next slide the door back down and gently push the bottom plates into the recesses on the appliance door.

Job done! Well almost. When you have got this far open the dishwasher door completely. You will see a plastic white cover caps on either side of the door. Remove these and drop a screw into the hole.. Make sure you measure the screw against the vanity door so that the screw does not go all the way through!! Now screw the appliance door to the vanity door.. Now the job is now complete!

Hope this helps!

Jan 01, 2009 | Danby DPAC120061 Portable Air Conditioner

2 Answers

Kenwood kdw243a dishwasher has an e3 error code


i have same prob,seen this elsewhere folks. apparently it's the temp sensor which MAY have failed. http://www.howtomendit.com/answers.php?id=134096
has to be cheaper than an expensive call-out and worth a try.

Dec 21, 2008 | Kenwood KW85 Air Conditioner

1 Answer

E6 error code displayed on Kenwood kdw243a dishwasher


The reset sequence used is:
1) Crack the door open.
2) Within 3 seconds press the following sequence - Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry
3) Close and latch the door
4) Press the cancel button (the circle with the triangle in it)

Nov 24, 2008 | Kenwood KW85 Air Conditioner

Not finding what you are looking for?
Kenwood KW85 Air Conditioner Logo

1,588 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Air Conditioners Experts

Michael McQuay
Michael McQuay

Level 2 Expert

111 Answers

ray gallant

Level 3 Expert

36236 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5625 Answers

Are you a Kenwood Air Conditioner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...