Question about Saws

Open Question

How do I change the blade in my Husky tile saw..mod.THD950l

How do I change the blade?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

thabrain
  • 76 Answers

SOURCE: Blade replacement on mk-170 tile saw.

take a pair of good vise grips and hook onto blade tightly, slide uo against back braket. that will hold the blade from spinning while you remove the nut, try bumping your ratchet/ wrench w/ a rubber mallet or hammer. hope this helps

Posted on Nov 05, 2008

  • 10865 Answers

SOURCE: crooked cuts

The bearings in your saw need to be replaced. I would contact a DeWalt store to obtain the parts or have them do the repair. You have an excellent saw there, well worth repairing. good luck.

Posted on Jan 28, 2009

  • 31 Answers

SOURCE: Cant get the old blade off

should be a blade lock button, if not i clip vise grips on mine let the table keep the blade from turning put wrench on nut and tap wrench with hammer see if ya can loosen nut good luck billy

Posted on Mar 24, 2009

  • 29 Answers

SOURCE: Tile Saw

i know blades on tile saws don't have to be super tight, i'm not familar with that kind of saw, i put a wrench on the nut and hold on to the blade with my hand and hit the wrench with a rubber mallet, and of course have the unit unplugged

Posted on Mar 26, 2009

woobie dog
  • 1273 Answers

SOURCE: I have a small ceramic tile saw. I have

Hello,

Look for a button that you can press to lock the shaft in position. When you depress the button, you may still have to revolve the blade and shaft until the lock engages the shaft. Then unscrew the bolt from the shaft. Some others have an Allen wrench well in the end of the shaft, and you can insert the allen wrench to hold the shaft while operatiln the wrench to loosen the blade. Some others have a slot in the shaft end for inserting a slotted standard screwdriver for holding the shaft while the wrench is used to loosen the blade.
One of these methods will be available to you!

Best regards,

--W/D--

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Huskey tile saw thd950l motor how much would it cost motor #c5d41884?


Take a look on amazon for sure. Amazon com Husky tile saw. If cant find just a motor, for sure there is someone to answer that question (someone who sells husky saws...). I hope this was helpful. cheers

Apr 12, 2011 | Husky Wet Tile/Stone Saw with with Laser...

2 Answers

MY SWITCH WENT OUT ON MY TILE SAW WHERE CAN i GET


You can get the part from husky website at:

http://www.huskysupport.com/products/product.aspx?ID=4

From there scroll down till you see part number
6102018
switch Knob for $5.38

Hope this is what you are looking for

Nov 30, 2009 | Wet International Husky 7" Wet Tile Saw...

3 Answers

The wet saw husky thd 950l wore out yhe bearing and make


I am a contractor who has used this saw for about four years. I just ordered the new motor for $79. The Husky has been a great saw. Don't waste your money buying some junk for Harbor Freight.

Oct 14, 2009 | Wet International Husky 7" Wet Tile Saw...

3 Answers

I have a husky thd950L wet tile saw and the on/off switch broke. Where can I find a replacement part?


I need to replace the ball bearings in my Husky THD950L tile saw. Please tell me where I can find them.

Oct 08, 2009 | Husky Wet Tile/Stone Saw with with Laser...

2 Answers

My Husky tile saw starts to cut straight and ends up crooked, have tried to adjust tray and still ends up crooked??????


Make sure both sides of blade are wet. Make sure blade is not worn out. Do not feed the tile excessively fast.

Next, and very important is that the blade arbor is at true to the table. If the saw is slanted in the least, the saw will track off course. I am talking VERTICAL slant.

Verify that the arbor bearings are tight and there is no "end shake"

Sep 22, 2009 | Wet International Husky 7" Wet Tile Saw...

1 Answer

Husky wet tile saw repair service


I need to order a part for my Husky wet tile saw. can someone give me an email address. web serches are a bust.

Aug 24, 2009 | Husky Wet Tile/Stone Saw with with Laser...

2 Answers

Cant get the old blade off


should be a blade lock button, if not i clip vise grips on mine let the table keep the blade from turning put wrench on nut and tap wrench with hammer see if ya can loosen nut good luck billy

Mar 18, 2009 | Husky Wet Tile/Stone Saw with with Laser...

Not finding what you are looking for?
Saws Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saws Experts

Tom Chichester

Level 3 Expert

33294 Answers

ray gallant

Level 3 Expert

41454 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1774 Answers

Are you a Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...