Question about Cyberhome CH-DVD 300 DVD Player

1 Answer

No vedio output but audio is coming out

I pressed the wrong button from that time there is no picture in the tv

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 80 Answers

Dear friends,
Press and hold STOP button on front panel of the player more than 5 sec. The player reset after 5 sec.

Posted on Mar 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I turn off pscan on a rca dro2oon DVD player


IMPORTANT:
If you don't have a Progressive Scan TV or you don't have the DVD player connected to the correct Input Jacks, and you activate Progressive Scan in the DVD player you won't see a picture! Don't panic-try the following:

First, press the PREV/VIDEO button on the front of the DVD player (it will go to the next video output option, which is an interlace output so a picture should appear on the TV screen). If that doesn't work, press and hold PREV/VIDEO button on the front of the DVD player for 3 seconds. Now, press the PREV/VIDEO button again (it will go to the next video output option, which is an interlace output so a picture should appear on the TV screen). If you still don't see a picture on your TV screen, make sure the yellow cable (provided) that is attached to white and red cable (called audio/video cables) is connected to the DVD player's PREV/VIDEO jack and the TV's Video Input jack. Change your TV channel to your TV's Video Input
channel that activates the TV's VIdeo Input jack where you have connected the yellow cable (page 9 of your manual has more information).This PREV/VIDEO jack on the DVD player always outputs interlace video, so you should see a picture on the TV screen.

As a last resort, you can reset the DVD player to the factory default settings:
Press and hold the STOP button on the remote control and the NEXT button on the front of the player at the same time - wait at least 5 seconds before you release both buttons

Sep 25, 2016 | RCA Televison & Video

1 Answer

Blu ray shows the "Blu ray Disc" Logo on TV screen and then just show a black creen


Hi! and welcome to Fixya!

It looks like your tv is unable to handle the output video resolution from your bluray. The reason why you do not have picture on the tv screen after the bluray disc logo appears.

You can follow the instruction below to set the video resolution on your player to its lowest resolution:

1. Using your bluray remote control, press the following buttons in order... STOP button (press and release) ....HOME button (press and release)....POP UP/MENU button ( press and release )
Note: press the buttons in order with 1 second interval. Make sure tv and bluray are ON when you try this. If first attempt nothing happens, try this again.

2. When the home menu screen appears after doing the above instruction, you can set the video resolution again manually. Follow the instruction:
Using the BD remote control press HOME button > then go to SETUP > select screen settings > then change OUTPUT VIDEO RESOLUTION to Auto > change also 24P OUT to 1080P // set the BD-ROM 24P OUTPUT to Auto

The next time you turn on the bluray player you will have picture again.

Let me know if this works!

Oct 24, 2015 | Sony Televison & Video

1 Answer

No Picture or audio...NOTHING!!!!


You must use the remote to toggle the player OUT of HDMI output mode to use the s-video output. The device displays black screen by default, so not possible to see the menu if using s-video. The manual states to press the 'Progressive' button to change modes. Unfortunately, you can't see what mode you're toggling through until you hit the right one (Toshiba blew it here!!). Power on the device WITHOUT a disk in (you can't change modes during DVD playback mode). There are four output modes, so press the 'Progressive' button on the remote and wait for 3 to 5 seconds for the player to switch output modes. Repeat this up to four times to cycle through the available modes. During one of the modes, you should see output to your screen through the cable hookup you've physically attached. You will also notice the led's on the front panel go on and off during the process at times. Good luck ~ and don't bother calling Toshiba support ... friggin waste of time talking to a recording that's dumber than Sh#@!!

Jun 11, 2009 | Toshiba SD6100 DVD Player

1 Answer

Sony BDP-S350 - no video..only audio on all outputs


This is button config for master reset without picture:
Home Left button x 3 Down button x 7 ok (centre button) ok Down button x 6 ok Left button x 1 ok ok wait a couple of seconds for settings to complete, when you switch back on you should have a picture and be back at language set up screen.
Hope this helps.

May 30, 2009 | Sony BDP-S350 Blu-Ray Player

1 Answer

How to change from tv to dvd mode


the difference between tv and av, is that av has no showers on the screen. if you change to av you will notice a blue screen, connect your yellow on vedio output and white/ red on audio out of tv
note- before connecting to a vedio touch a tip of your vedio cable some lines will show on your screen, if touch your audio tip harming noise will sound on your tv. if this two happens then you know that your cables are okey. hold your channel button on your tv, channel will start runing after all rf channels finish, tv will go to av.

Oct 13, 2008 | Sony DVP-NS50P DVD Player

1 Answer

S-vedio output connected with TV does not give any sound. Is the S-vedio output connection with a TV not enough for sounds?


Right, S-Video is higher quality video only, sound still goes out through 'red'/'white' RCA phono plugs near the other (lower quality) 'yellow' video out

Sep 13, 2008 | Toshiba Televison & Video

2 Answers

No picture


I have my television outputs connected to the inputs on the ILO. I then select that set of inputs with the SOURCE button rather then using the built in tuner. Make sure you connect the Video closest to the audio inputs(or... least confusing, try the three front inputs) Hook antenna to tv

Jun 28, 2008 | iLO DVDR05 DVD Recorder

1 Answer

Help!


Try pressing the HDMI button on your remote a couple of times, pause about 5seconds after each press it might be slow to change. If this doesn't work try connecting just the yellow lead(composite video) into the DVD player to the TV like the old days, probably AV1 or AV2 in the back of the TV. Then access the setup menu(setup button on remote). This will bring up a menu. Use the down arrow on the remote until HDMI setup is highlighted. You should then get a selection to turn HDMI on and select the different outputs(576, 720p, or 1080i). You might actually find the picture to be worse on some DVDs.

Apr 06, 2008 | Televison & Video

1 Answer

Dvd burner


Can you try just running a/v cable from your tv output to the inputs on the ilo, then whatever you watch on your tv you can record on your dvd burner. My new SDTV doesnt have audio out except Coax so this won't work for me on that tv. Why doesnt the newer tv's have audio AND video outputs???

Oct 30, 2007 | iLO DVD Recorder DVDR05

2 Answers

Protron PD-800 DVD player


On the remote control of the DVD player, just press the P-scan, reset or video SW button.. That would fix it... If you have screen kumping problem then please try this following steps... Press the setup Down arrow once Enter Down arrow 1 time Enter Up arrow 1 Enter Set up

Jul 04, 2006 | Protron PD-800 DVD Player

Not finding what you are looking for?
Cyberhome CH-DVD 300 DVD Player Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cyberhome Televison & Video Experts

zappal

Level 1 Expert

48 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6364 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Cyberhome Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...