Question about Roper REX4634KQ Electric Dryer

1 Answer

Will not start

I push start button but will not start

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Roper Master
  • 8,220 Answers

Open the door and wiggle the door switch. It should click. If it does not then that could be the problem. If the lid switch is audible then next thing to do is yank out the fliter and look for lint. Remove the vent pipe and look for lint. If you notice a lot of it the dryer may have over heated. Remove the power and take the rear dust cover off. You will find the fuse on the blower housing right next to the control thermostat. It is white skinny with the screw and 2 small wires. In the same circit as the door switch it kills the power going to the motor IF the lint inside the blower housing/filter chute obstructs the aitflow to the point that the temp inside is over 350f. Just simply swapping out the blown fuse won't get it fixed. You must remove the filter chute and clean it out as seen in this pictorial:
ROPER DRYER CLEANUP

Posted on Dec 31, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set the clock on a MT01


To set the clock
1. Turn the key to "ON".
2. Push the "SELECT" button and
"RESET" button together for at
least two seconds.
3. When the hour digits start flashing,
push the "RESET" button to set the
hours.
4. Push the "SELECT" button, and
the minute digits will start flashing.
5. Push the "RESET" button to set
the minutes.
6. Push the "SELECT" button and
then release it to start the clock.

Oct 22, 2013 | Yamaha MT-01 Motorcycles

1 Answer

PUT IN TIME/DATE ON CVS MODEL KD556 SKU 800231 BLOOD PRESSURE MONITOR, THERE R 2 BUTTONS, START & MEMORY : NO SET BUTTON


On your model, hold the "start" and "memory" buttons at the same time. After about 3 seconds the month will start flashing in the window. Push the "memory" button until it gets to the month you want. Then hit the "start" button and the day of the month will flash. Push the "memory" button until the correct day of the month comes up. Push the "start" button again, and the hours will flash. Push the "memory" button until the correct hour comes up. Do the same for minutes, and the next time you push "start" it goes into ready mode.

Apr 07, 2012 | Health & Beauty

1 Answer

How do I adjust the time on a 2005 yamaha roadstar digital clock?


With the key on.......

1) Push the select button and reset button together for at least two seconds.
2) When the hour digits start flashing push the reset button to set the hours.
3) Push the select button and the minute digits will start flashing.
4) Push the reset button to set the minutes
5) Push the select button and release it to start the clock.

Dec 14, 2010 | 2005 Yamaha Road Star Midnight Silverado

1 Answer

Adjust the time clock on the 2005 xt660x please


G'Day Dutchgbg

Here is a quick guide to set the clock

1: Push the "select" button and the "reset" button together for at least two secounds.

2: When the hour digits start flashing, push the "reset" button to set the hours

3:Push the "select" button to fix the hours, and the minute digits will start flashing.

4: Push the "reset" button to set the minutes

5: Push the "select" button to fix the minutes, and then release it to start the clock.

regards robotek

Apr 09, 2010 | 2005 Yamaha XT 660 X

1 Answer

Push start button the dryer will tumble, but immediately stops


there is a relay that latches on when you push the start button .. that relay is released by the "door open" switch .. i would suspect that the "door open" switch is bad .. thats usually a button that is pushed in when the door is closed ..

Sep 19, 2009 | Kenmore Dryers

1 Answer

Kenmore Dryer stop running when release the start button


I have whirlpool dryer, when i push the start button it will start but only stay on for part of the drying time. no the start button make noise when push and after keep trying it stop.

Dec 30, 2008 | Whirlpool LEQ9858P Electric Dryer

1 Answer

Lg lre30451sw oven the start button doesn't work


This happened to me on Christmas Day morning & it happened once before. I finally remembered how I fixed it. Push the "Clear" button & then push the "Start" & keep it held in until you see the lock button light up (takes awhile) & then push the "Clear" button again. After I did this the "Clock" worked again - reset the clock to the correct time & push "Start" Then click on "Bake" set your temperature & push "Start". Hope this works for you. It got me out of cooking Christmas Dinner, but I fixed it today!!

Sep 25, 2008 | Ovens

Not finding what you are looking for?
Roper REX4634KQ Electric Dryer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Roper Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Sal DeAngelo

Level 3 Expert

2254 Answers

Are you a Roper Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...