Question about Kenmore 15944 Top Load Washer

1 Answer

Aggitator won't work and won't spin/ drains ok

I have a 90 series kenmore washing machine model # 110.26912691
the aggitator won't aggitate and it won't spin but it does drain. What can be the problem. I washed one load of work shirts and pant etc. on the permanant press cycle and it seemed to work fine. the next load was whitesand that is when it seemed to quite on me. Any ideas or suggestions?

Thanks
Terri Bester

Posted by on

  • pbester Jan 18, 2009

    Coupling douse not seem to be the problem. Any other ideas

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 161 Answers

Coupling is bad.
There is a coupling between the motor and the transmission. When this part breaks then it will pump the water out but won't spin or aggitate.

Posted on Jan 18, 2009

  • Ron Buice
    Ron Buice Jan 18, 2009

    Check the lid switch. The two wires going to thw switch can be jumped to see if it will work.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why agitator not trning in kenmore washing machine?


If the spin cycle works, but the unit only fails to aggitate......the problem is most likely a clutch or transmission problem. If the unit neither spins or aggitates, you could have a broken belt or even a defective lid switch. Sometimes a model will have broken dogs, or cogs in the aggitator base. To check this, with the machine off..reach into the machine tub..grab the aggitaror and try to turn it manually by hand. If you can turn it and also feel a sensation such as a gear slipping or teeth not properly taking hold or meshing, the cogs or dogs may need to be replaced that are under the aggitator itself. Best Wishes

Sep 01, 2014 | Washing Machines

1 Answer

Aggitator does not work, makes sounds


if the spin cycle works it's probably a broken belt, otherwise you need a new motor

Aug 14, 2009 | Kenmore Washing Machines

1 Answer

Will not agitate 110 92587210 Kenmore Washer


I have 2 words for you: "dog ears".

the dog aggitation ears are what cause the aggitator to aggitate. Those things wear down and not grab after time.

Pretty easy to change out. You just need to pull the aggitator out and change the 4 little plastic ears. Good luck :)

Jul 13, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

My Kenmore model 80 washer won't aggitate but spins and drains without issue. The aggitator tries to move but acts like there is a gear stripped or something.


you will need to purchase an agitator replacement kit for your washer and, the clutch will need to be replaced as well. these components are damaged and, replacing them will restore your units agitation functions.

Jun 07, 2009 | Kenmore 15944 Top Load Washer

1 Answer

Spin Cycle Works Some


you have a broken coupler...this is a plastic and rubber part that connects the motor to the transmission.  A $20 part

Jan 24, 2009 | Kenmore 15864/15862 Top Load Washer

1 Answer

Kenmore series 70 washer won't stop agitating when lid Is lifted.


I have a Series 80 and when I lift the lid it does not stop aggitating when in wash mode. When I lift the lid it does stop spinning when in rinse mode. As designed.

To stop wash-mode aggitation at lid-lift, using the existing lid switch and other electrical components, is not easy and not recommended. I can think of a way to do it (triple-pole lid switch) but I will not detail the idea .. for safety concerns.

To stop aggitation, simply use the main settings dial control. You'll save money and possibly prevent a fire hazard!

Jan 23, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Aggitator operates as soon as the washer is turned on.


Hello,

Your pressure switch hose maybe be plugged. This is happening because your washer thinks it's full of water.

Remove the clear hose from the pressure switch behind the control panel and blow through the hose. You are basically going to blowing air through the hose and into the wash tub. This will clear any restriction that is in the hose.

This is a common problem and a simple fix for your issue.

If you have anymore questions about this please ask. I will be more than happy to help you further.

Thanks

Jan 12, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

The aggitator (sp?) isn't turning...the rest seems to be working (spin & fill). How do I fix it and is it worth fixing? Model LBT6133A Whirlpool Washer


Go under the aggitator inside the tub and pull out the aggitator it self and check out see if the teeth are strip,If the teeth are strip on the aggitator replace it. If is on the other side then it's not worth repairing. All you need to do is just pull on the aggitor from the bottom.

Apr 26, 2008 | Washing Machines

1 Answer

Washine mashine aggitator


Rob, sounds like you need an agitator repair kit. Not a hard job, under the dispenser cap you have a set of ears, spring and plastic bearing. The kit is cheap, you can find it here http://www.repairclinic.com/0080.asp Catriver...post back

Dec 03, 2006 | Kenmore 15864/15862 Top Load Washer

Not finding what you are looking for?
Kenmore 15944 Top Load Washer Logo

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Jesus  Colon
Jesus Colon

Level 1 Expert

12 Answers

Fred Sops

Level 2 Expert

271 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...