Question about Bosch Hammering

1 Answer

Lack of power

I own a bosch brute 0611034139 and it lacks power ahen laid on cement it just taps the cement can you direct me to the problem or what to look for

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Check the brushes and armature if it isnt that abused you can get away with cleaning the armature and replacement of the brushes...

Posted on Jan 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi I have a Bosch gbh8 dce. Sds max breaker/drill. It works but not much power coming from it. Any ideas. Thanks.

Motor bearings can cause lack of power eventually damaging the windings in the motor.

Feb 02, 2017 | Bosch Drills

1 Answer

How to light the Bosch TF250 pilot light

I believe this is a hydro-sparker pilot ignition then burner on when T-Couple/Flame Sensor acknowledges pilot lit.
W/O the signal feedback the Gas Valve will not open and light burner.
This is a Technician Service Job as you have insufficient knowledge to DIY this potentially dangerous LP/NG Control Valve/Sparker Assembly
I assume that lack of knowledge by your lack of a Manual for the Unit
You cannot force ignition on a hydro-sparker manually.

Sep 08, 2014 | Bosch Water Heaters

1 Answer

Newly laid cement driveway puddles and top brushes up

By puddling, do you mean water stands on it in spots? And, do you mean by top brushing up that the concrete top layer is flaking off. If so, water puddles where there are low spots and flaking is generally due to over working the top of the concrete as it is being finished. Some poor contractors have also been known to sprinkle cement on top of concrete to make it look like it has been finished better. When this happens it will pop lose and flake off.

Apr 27, 2014 | Refrigerators

1 Answer

List of nouns

I lived in Master Hugh's family about seven years. During this time, I succeeded in learning to read and write. In accomplishing this, I was compelled to resort to various stratagems. I had no regular teacher. My mistress, who had kindly commenced to instruct me, had, in compliance with the advice and direction of her husband, not only ceased to instruct, but had set her face against my being instructed by any one else. It is due, however, to my mistress to say of her, that she did not adopt this course of treatment immediately. She at first lacked the depravity indispensable to shutting me up in mental darkness. It was at least necessary for her to have some training in the exercise of irresponsible power, to make her equal to the task of treating me as though I were a brute.

Jan 10, 2014 | Toys

1 Answer

Lack of power

hi. I have a Vauxhall Vectra 2.2sri direct, it has lack of power and misfires. have changed coil pack and have been told it could be high pressure fuel pump. can anyone advise me as this car has already cost me a lot of money. many thanks

Jan 02, 2014 | 2001 Volkswagen Passat

1 Answer

Losuing over drive lack of power hard starting must hold pedal to the floor

Does it start better after sitting overnight? Is it missing at all? Check engine light? Hard starting could be fuel pump, also lack of power could be lack of fuel. If it starts better after sitting overnight, could be block catalytic converter. That would also explain lack of power. If you have to hold gas pedal half way down trying to get speed would explain why it is not going into overdrive. Hope this gives you some direction.

Jan 04, 2012 | 1996 Chevrolet C1500

1 Answer

Bent rod

if it is an air or gas hammer... probably lack of lubrication...

Feb 09, 2009 | Bosch Brute Breaker Hammer 11304

8 Answers

Engine lacks power

check out cat converter

Aug 31, 2008 | 1994 Honda Civic Del Sol

Not finding what you are looking for?
Hammering Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Hammering Experts

John Trevino

Level 3 Expert

1388 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 2 Expert

36 Answers

Are you a Bosch Hammering Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides