Question about Car Audio & Video

Open Question

My PPI amp is in protection mode. How can I reset this amp?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
XSdB
  • 80 Answers

SOURCE: ppi amp

Here is an archive od PPI PowerClass manuals...

http://narbi.free.fr/manuels/Amplis/Precision%20Power/Serie%20Powerclass/

Posted on Jun 12, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just got my PPI dcx 300.2 amp back and i hooked it all up, and connected the fuse back in and started the truck, the amp turns on but the red light starts blinking and says clip out. The amp doesnt smell...


Are you sure everything is correctly connected. If you are running the amplifier in bridge mode then take note that the load to the amplifier can be no lower than 4OHM. dreamsystems

Feb 25, 2011 | PPI DCX-300.2 Car Audio Amplifier

1 Answer

My PPI4240 has gone in to protect mode (red light is on). How do I get it out of protest mode?


protect comes on bfor several reasons:

1. short circuit/crossed speaker wires- examine the speaker cables very carefully, paying particular attention to loose strands at the ends that may be crossing.

2. blown speaker/fried vioce coil- push in on the speaker and it should push down about an inch with no resistance befopre bottoming out. if there is resistance, and/or it feels scratchy/rubbing when pushing in then the speaker is blown.

3. blown amp.

Nov 25, 2010 | PPI4240 Car Audio Amplifier

2 Answers

How do I reset from the amp protect mode Onkyo receiver TX-SR600?


How do I reset my amp / receiver from protect mode ?

May 07, 2010 | Onkyo TX-SR605 Receiver

1 Answer

Amp will not come on keeps going into protection mode


nice amp you have to be leaking something from the car onto it. it should not get wet at all. did you go through the car wash and your whether striping leaks??

Apr 04, 2010 | PPI D2000/1 1-Channel Amplifier Car Audio...

1 Answer

My ppi 2200 power light flash's on and off


yes you have a internal fault of the amp. the circuit that puts it into safe mode is bad and that is a very small chip on the board know as a op amp. needs to be repaired.

Feb 03, 2010 | PPI PCX-2200 Car Audio Amplifier

1 Answer

RODEK AMP PROTECTION


have you checked your speaker connections and any other connection for shorts or multiple ground loops. cause that will definately cause the protection mode.

Mar 03, 2009 | PPI PCX-280 Car Audio Amplifier

1 Answer

PPI AMPLIFIER NO SOUND PSX-280


make sure the remote wire from the deck is in the amp but move your ground wire to a new solid metal location you may have to scrape the paint surface where the ground is going to go but it will stop protect mode and run properly (make sure to bolt it down by its self no other wires just the ground from amp) also make sure the ground wire is bigger than the power wire
hope this helped

Mar 03, 2009 | PPI PCX-280 Car Audio Amplifier

1 Answer

Ppi amp


Here is an archive od PPI PowerClass manuals...

http://narbi.free.fr/manuels/Amplis/Precision%20Power/Serie%20Powerclass/

Jan 30, 2008 | PPI PC2600 Car Audio Amplifier

1 Answer

Need owners manual


Here is an archive of PPI PowerClass amp manuals...

http://narbi.free.fr/manuels/Amplis/Precision%20Power/Serie%20Powerclass/

Jan 30, 2008 | PPI PC2600 Car Audio Amplifier

1 Answer

AMP


If the amp gets hot or goes into protection with no input signal and no speakers/wires connected to the speaker terminals, the amp likely has shorted output transistors. It's not a complex amp. Any reputable shop should be able to repair it.

Sep 16, 2007 | PPI DCX-600.4 Car Audio Amplifier

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4869 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...