Question about GE 28111 Cordless Phone

1 Answer

Validation I bought a GE Cordless Phone Model 28111 whick came, as I am sure you know, with 2 handsets. I purchased an additional phone and I cannot validate it. I have followed the directions too many times and still nothing.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

I would assume this could have been a product that was returned to the company that you purchased it from. Follow these instructions. 1. 1. Disconnect power from the base by pulling the plug out of the back of the unit. 2. Press and hold the Page button and while holding the Page button reconnect the power. 3. Continue to hold the Page button until the charge/in use light flashes rapidly. 4. Release the Page button. 5. Press and release the page button on the base once. All handsets are de-registered and HANDSET NEEDS REGISTRATION shows in the display. Then From the Handset Setup Menu: 1. Press the caller ID-volume ( 6 or 5) button to scroll to the REGISTRATION sub-menu. 2. Press the mute/program button to enter the menu. REGISTRATION 1YES 42NO - - -shows in the display. The default setting is 2NO. 3. Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the caller ID-volume ( 6 or 5) button to scroll to 1YES or 2NO. 4. If you select YES, press the mute/program button. HOLD BASE PAGE FOR 5 SECONDS, THEN PRESS HANDSET PROGRAM shows in the display. (Your handset should be held near the base during registration process.) 5. Press and hold the page button on the base unit until the charge/in use indicator flashes. Press the handset mute/program button. REGISTERING shows in the display. HANDSET X REGISTERED shows in the handset display, where X is the handset number. You may now rename your handset. (Refer to Step 3 & 4 of Handset Name Section) NOTE: IF you are re-registering the handset through the handset menu; to rename your handset you must go to the Handset Name Section and start from the beginning step. I understand that you have tried the registation process. Sometimes with electronics, you have to start from ground 0, before it will work correct again. If there are further questions or comments, please post here. Please rate this solutn through fix-it. Thank you

Posted on Jul 08, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I love my GE Model 28111 Series DECT 6.0 Cordless Handset Speakerphone System. However, I goofed the other day and accidentally left it outside and then it poured. Needless to say, it is totally shot. ...


Your GE phone doesn't have an accessory handset. Unfortunately you cannot replace it with just one handset. If the phone is within warranty, kindly return it to the manufacturer and have it replaced.

Sep 04, 2011 | GE 28111 Cordless Phone

1 Answer

Says line in use


unplug everythingthen plug it allback in then press the mute button on the phone (program) then go to hand set setup... then go down to de authorize and remove the link..... then reauthorize it

Jul 24, 2008 | GE 28111 Cordless Phone

1 Answer

Model 28111 series dect 6.0 GE phone


I'am subscribed to three way calling from my phone company, but forgot which button to push to connect three way call on my phone is it the green talk button that is in the middle of my phone.

Apr 30, 2008 | GE 28111 Cordless Phone

2 Answers

New Voice Mail flashing light


What worked for me was to call my phone from another phone and leave myself a voicemail. I then went in and retrieved and deleted that voicemail. Once I hung up from my voicemail service my handsets reset about 10 seconds later.

I hope this helps!

Apr 05, 2008 | Uniden Cordless Phone

1 Answer

GE MODEL 28112 DECT 6.0 CORDLESS PHONE


I contacted GE today and they told me how to get the caller ID to work on the additional handsets. You must follow these steps in the exact order given.

#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes.

reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in. It takes about another 10 minutes after that before all phones start recognizing caller ID but it now works fine.

Mar 26, 2008 | GE 28112 Trio Cordless Phone

5 Answers

GE DECT 6.0 GHZ cordless fone (model 28111) don't ring


There is a Do Not Disturb button on the base unit. Press it to turn the feature on and off.

Feb 22, 2008 | Lands Phones

2 Answers

GE 28110EE1 DECT 6.0 line in-use


Same problem with mine too! and without paying $$ I can't get an answer....nice product!!!! (junk)

Feb 08, 2008 | GE 28111 Cordless Phone

2 Answers

Caller ID Problem on the GE2811 Twin cordless phone system


How to get the caller ID to work on the additional GE DECT phone handsets. You must follow these steps in the exact order :
#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes. reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in.
It takes about another 10 minutes after that before all phone handsets start recognizing caller ID.

Oct 23, 2007 | GE 28111 Cordless Phone

1 Answer

GE 28111 Twin Cordless Phone "Line In Use"


I had the same problem. I went to each handset and pushed the talk button. After I got a dial tone, I pushed it again to stop the dial tone. The message went away.

Aug 14, 2007 | GE 28111 Cordless Phone

Not finding what you are looking for?
GE 28111 Cordless Phone Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Lands Phones Experts

Cindy Wells

Level 3 Expert

5528 Answers

Dudeman321

Level 2 Expert

233 Answers

Marvin
Marvin

Level 3 Expert

81400 Answers

Are you a GE Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...