Question about Watches

Open Question

How do i shorten accurist charm bracelet strap

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

indays
  • 111 Answers

SOURCE: Shorten strap of Casio Edifice EF-518 watch

good morning ! thats verry easy to make shorter !just look the possition of arow and push the pin to out use the pointed tool and anvil to releas the pin ! thank you !god bless !....

Posted on Sep 02, 2008

  • 1 Answer

SOURCE: I have a stainless watch bracelet for the Casio

E ALLORR WATCH REPAIR NEEDS TO A JEWELER/WATCH REPAIR SHOP/CLOCKS EVEN...NOT WALMART OR SO CALLED RIP OFF STORES SELLING THESE FOREIGN PIECES OF CRP. IT WILL GET DONE RIGHT AND NO DAMAGE TO YOUR COMMUNIST // POVERTY TOOK JOBS AWAY FROM YOUR HOME COUNTRY. JOBS FROM YOU, MOM, DAD, GRANDPA N MA, YOUR BUDDIES N GIRLS, NEIGHBORS...THINK ABOUGHT IT EXPENSIVE AND YET CHEAP ****KEY WORD CHEAP INFERIOF TO AMERICAN MADE PRODUCTS WERE NOW GOING DOWN WITH NEW POLITICAL BLOOD HELP TO BELOW 3RD WORLD COUNTRIES. GET REAL FIGHT BACK PAY A BIT MORE FOR THR REAL DEAL, USE YOUR BRAINS NOT THE TRENDS THESE **** ARE SHOWING YOU----DID U KNOW THEY DON'T PAY NOT ONE PENNY THEY GIVE EM TO THEM---SHAMEFULLY FAIR TO YOU FLIPPING BURGERS N SCRUBBIN FLOOS 3 WEEKS OR MORE TO PAY FOR YOUR AND FREE 2 THEM FOR WEARING IT FREE ADVERTIZEMENT!!! SUPER FAIR THESE PEOPLE LAUGH IN MEETIN GS AT THE STUPIDITY OF AMERICNS NEVER CATCHING ON----JUST LIKE THIS SO CALLED HEALTH CARE! OF OBAMA---NO IT WILL BE THE NEXT STEP TO TOTALLY CONTROLLING EVERYONE IN THE UNITED STATES. CHECK OUT CANADA AND MEXICO....THEY COME HERE FOR CARE...I HAVE A FRIEND IN CANADA HAS BEEN WAITING OVER5 YEARS FOR A SURGERY THAT IISN'T GOING TO HAPPEN NOW THEY SHOULD OF DONE IT WHEN UT WAS FIRST FOUND, LITTLE CHILDRE, OLDER FOLKS, GRANDMA/PA, EVEN AUNT BETTY---GONE IN A FEW MONTHES YOU HAVE TO PAY FOR MEDS, DOC VISITS,BUT JUST NO APROVAL NO HOPE MAYBE IN YEAR OR TWO OR MORE WELL SEE. OH THE MONEY YOU AND I PAY IN FOR PREMIUMS AND EXTRA TAXES GOES TO HIRE MORE PEOPLE TO DECIDE WHO TO LET DIE FIRST....FABULOUS PLAN....SOUNDS LIKE **** TO ME!!! WATCHES=LINKS ARROWS GO UP TAKE TWESSORS AND PUSH OUT DIRECTION OF ARROW LIKE 3 NED OUT THEN GO BACK AND TAKE LAST AND FIRST LEFT JUST REPLACE AS TOOK APART ALL SET TO GO....

Posted on Dec 23, 2009

mcdevito75
  • 1970 Answers

SOURCE: How do I shorten my Ice watch strap?

mcdevito75 here, I imagine you mean a Band (metal) they can be shortened by removeing links from the band itself, you"ll need a specific tool called a link remover tool. they are available on ebay. However by the time you get the tool and the time to do the work, and if you don"t do any work on watches, the best bet is to look for a small watch repair shop in your area to remove these links. Hold onto the removed links for later replacement. If it"s a Strap (material) on your watch, say, leather, rubber etc. simply cut the excess strap at an angle with scissors.

Posted on Jul 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How or where do I get a new watch strap for above.


Duplicate straps for a great many inexpensive fashion watches are not available and either a universal strap or bracelet used or the whole watch discarded or replaced. Sometimes a junk shop or thrift shop will yield something salvaged that could resemble the original. Sometimes jewellers and watch repairers collect junk watches for parts so asking around locally could bear fruit.

More expensive watches might have replacement straps or bracelets available from the manufacturer or dealer for a limited time as a spare part.

Replacement straps or bracelets should be available for the best watches from the manufacturer for a considerable time.

Unless your watch is a Rolex or an Omega or similar I suggest you start your search at your local watch repair shop.

Sep 04, 2015 | Watches

1 Answer

How do I shorten ******** my Tag Heuer Formula 1 watch?


Take a look at the watch from the side where the band attaches to the buckle. You should see four holes with one of them having a visible pin in it where the band is connected to the buckle. Moving the band to the right will shorten it moving it to the left will make it bigger. To move it simply get something that you can push the pin in with like a paper clip. Push the pin in and the band should come out move it to the left and push the in again and simply move the band into proper position. Once you do that the pin will snap back into place. If that does not adjust it enough go to your local watch store and they can remove links from the bracelet for you. Shouldn't cost you more than $10.

Dec 14, 2013 | Tag Heuer Formula 1 CAC1111.BA0850 Wrist...

1 Answer

Omega 196.0167 cal 1342


The watch part number and a knowledgeable watch maker will provide the correct bracelet. If you WANT a leather strap most models can accept one - unless the case is sculpted to integrate seamlessly with the bracelet, in which case you may not be able to insert the spring bars that are necessary to mount the strap.

Sep 09, 2012 | Omega Watches

1 Answer

I'm trying to find out the measurment of the band of the watch because I want to replace it, and althoug I measured it myself, I find different measurments on the internet


Measure between the lugs, (where the currently installed bracelet/strap is installed. It should be measured in millimeters as that how all straps/bracelets are measured. Standard men's widths are 20, 22, 24 and some 26mm. There are of course, variations like proprietary bracelets and straps made to fit watches which will only accept the proprietary size made for it. These are usually much smaller (18, 14, 16mm) and integrated into the watch body design.

Jun 07, 2010 | Citizen Perpetual Calendar BL5260 50E...

1 Answer

How do i shorten a Casio waveceptor metal watch strap please?


You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have the pins instead of screws.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please.

Jul 31, 2009 | Casio Watches

1 Answer

I am trying to remove a link from the strap to make the strap fit


You may or may not have arrows inside bracelet. Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
If you do not want to do it yourself, any jeweler will do it in a matter of few minutes.
Don't forget to rate, please.

Mar 23, 2009 | Casio Watches

1 Answer

Trying to shorten stainless steel watch strap


You may or may not have arrows inside bracelet.Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and start to unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet or adding extra link(s) make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
Don't forget to rate, please.

Feb 27, 2009 | Bulova Watch

1 Answer

Shortening stainless band for 1st generation Tissot Le Locle


Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and start to unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet,make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
Don't forget to rate, please.

Jan 04, 2009 | Tissot Le Locle Automatic Chrono Large...

1 Answer

Need to shorten the band on a Timex Ironman Triathlon


These pins will definetely come out- poke a bit harder. You may have arrows inside bracelet.Arrows are pointing the way the pins must come out.
First you have to find out what sort of pins or even screws are used to keep links together.
Examine both bracelet sides and find the side where pin ends have a groove.
Start with a tiny screwdriver and start to unscrew one of the screws. If it turns, but doesn't come out, that means you have a pins instead.
For removing pins the best would be pin removing tool (approx.5GBP on ebay), but it's possible to do the job without it.
Take a hardened steel needle and blunt the sharp end to the approx. size of pin end diameter using any sharpening stone or sandpaper. Get an old towel and fold it to make a soft base for work (like small cusion). As you don't have a special bracelet holder you will need a pair of helping hands to hold the bracelet steady upright. You will need small hammer and pair of flat nose pliers as well.
NOTE: The pins MUST be driven split end out first, not vice versa. Make sure that the grooved pin ends are facing towel, not the needle and hammer!!!
Now place the watch on the folded towel, take that needle and smallest hammer you have and start driving the pin out using light blows. Do Not hit hard, as you will brake the needle, scratch your watch or even injure yourself. Watchmakers are using 45 gram hammer, so, calculate your strength of blows.
After a few blows check if the split end is coming out and when you see that the end is long enough to grab it with pliers, pull the pin out with pliers. When pulling, do NOT turn pliers, as pins tend to brake when twisted. Use firm grip and your strength to pull the pin without twisting.
After shortening the bracelet,make sure that the pins go back EXACTLY the same way as they came out- the blunt end first in the hole and the split (grooved) end last. Before doing that check remaining pins in bracelet to make sure that you put them back from the right side of bracelet.
It is recommended to use plastic hammer to drive pins back in or you will scratch or damage bracelet. If plastic hammer is not available use an old toothbrush handle (or some plastic item) as an absorber. Simply put pin into the hole as deep as you can with your fingers, put the toothbrush handle on split pin end and hit handle, not the pin.
Make sure that pin ends are flush with bracelet. If needed- hit few more times.
Job done!
Don't forget to rate, please.

Jan 04, 2009 | Timex Ironman Triathlon 50 Lap Digital...

Not finding what you are looking for?
Watches Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Jimmy Accardi

Level 2 Expert

101 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...