Question about HP OfficeJet 6210 All-In-One InkJet Printer

3 Answers

Printer stuck on error message "Remove and check cartridge."

I have replaced both color and b/w cartridges--twice--and still this message is displayed along with a flashing orange lighted exclamation mark. I have also tried restarting both printer and computer, together and separately. I am wondering if I pushed the new cartridge in too hard when I initially was replacing the old one. But that is the only thing left I can think could have caused this problem, unless it is a problem with the printer itself that will require taking it to a shop for repairs. It has been a good device for the several months we have owned it. Please advise Bo Butler

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

I understood your issue. This problem occurs when suppourted catridges are not used and even if you use refilled catridges. Even try to perform usb refresh and power cycle.

Posted on Aug 09, 2007

Ad

I have replaced both color and b/w cartridges--twice--and still this message is displayed along with a flashing orange lighted exclamation mark. I have also tried restarting both together and separately. I am wondering if I pushed the new cartridge in too hard when I initially was replacing the old one. But that is the only thing left I can think could have caused this problem, unless it is a problem with the printer itself that will require taking it to a shop for repairs. It has been a good device for the several months we have owned it. Angelo Chiarelli

Posted on Aug 05, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 186 Answers

Remove and check what? With the machine off see if you can slide the printhead left to right freely. Make sure nothing is interfering with it. Also check and make sure there is not a paper jam any where.

Posted on Jun 26, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Received an error code 50c on my Dell printer


Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

Thanks for all the ideas and help ; )

Apr 27, 2010 | Dell A940 All-In-One InkJet Printer

1 Answer

Lexmark 6170 Cartridge Error 50C How to resolve?


"Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Apr 17, 2010 | Lexmark X6170 All-In-One InkJet Printer

1 Answer

Cartridge error 50c


Hi there Error 50c
Please try this.

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Dec 22, 2009 | Dell A940 All-In-One InkJet Printer

1 Answer

Dell A940 prints black but doesn't print in color. I installed a new color cartrige and the 50c error went away, but still doesn't print in color...


Hi there Error 50c
This is for yours.
Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Nov 20, 2009 | Dell A940 All-In-One InkJet Printer

1 Answer

Installed a black ink cartridge and the printer shows the message 'black cartridge missing' and also says 'cartridge error: error 50c'


Hi there Error 50c

Can only gave it a try.

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Nov 06, 2009 | Dell A940 All-In-One InkJet Printer

1 Answer

Cartride error 50c on display


Hi there Error 50c
ok ok try see if this works
Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Oct 31, 2009 | Dell A960 All-In-One InkJet Printer

1 Answer

Error 50C being displayed and the Printer will not print. I have replaced both Cartridges with no joy. What should one do?


Hi there Error 50c

Regarding the Dell A940 "Error 50c"....the user guide doesn't seem to mention "Error 50c". They do, however, mention a "Cartridge Error" on page 52 of the manual. They claim this means that the printer has detected a short circuit (fuse/resister) in the cartridge. As you may or may not have noticed in the manual, this is what they recommend doing about it:

1) Press Power to turn the printer off.

2) Lift the printer cover/lid (scanner unit) until the scanner support holds it open.

3) Turn the printer on.
The ink cartridge carrier moves and stops at the loading position unless the printer is busy.

4) Remove the color ink cartridge.

5) Lower the printer (scanner unit) until it is completely closed.
If the error message displays again, replace the black cartridge with a new black cartridge.

If the error message does not display, repeat steps 1–3 and then go to step 6.

6) Reinstall the color cartridge and remove the black ink cartridge.

7) Lower the printer (scanner unit) until it is completely closed.

If the error message displays again, replace the color cartridge with a new
color cartridge.
If there is no error message (indicated by flashing lights), repeat steps 1–3 and then reinstall both ink cartridges.
8) Lower the printer (scanner unit) until it is completely closed.

If you get the error message again, while both cartridges are installed, replace both of the cartridges.

Basically, what they want you to determine is,....if the short circuit is with the "black ink" cartridge or the "color ink" cartridge and then replace the cartridge that has the problem.

You may have to buy a new cartrige.
Please all I ask is call back and just gave a vote, it will gave me some satisfaction to know am helping some one, so I will keep on helping.
All The Best: Pineworks

Oct 07, 2009 | Dell A940 All-In-One InkJet Printer

1 Answer

Brought c5180 two 1/2 years ago. starting using product 8 months ago, printed maybe 500 pages. replace ink when needed. now printer say i need to replace cyan ink which i did twice. brought it in for...


Complete the steps below in the order presented to resolve the problem. It might not be necessary to complete all of the steps.
NOTE: The printer will not operate unless all six ink cartridges are installed. Also, HP cannot guarantee the quality of refilled or remanufactured ink cartridges. Step one: Reset the printer CAUTION: Do NOT perform any other type of reset on the printer before the ink initialization process has been completed.
  1. Without turning the power off, remove the power cord from the back of the printer and from the wall socket.
  2. Wait 30 seconds and reconnect the power cord to the printer and to the wall socket. Turn the unit on if it is not already turned on.
  3. Check the printer for the error message. If the error message still displays, go to the next step.
Step two: Clean the cartridge contacts
  1. Lift the top cover. Figure 1: Lifting the top cover c00372271.gif
  2. Locate the ink cartridge indicated in the error message. Squeeze the gray tab below the cartridge slot to release the latch and then lift the latch. Figure 2: Unlatching the cartridge c00372272.gif 1 - Black cartridge 2 - Color cartridges
  3. Remove the cartridge indicated in the error message. Figure 3: Removing the cartridge c00372273.gif
  4. Gather the following cleaning materials:
    • Distilled, filtered, or bottled water. Do not use tap water, alcohol, or platen cleaners.
    • Lint-free cloth or swab. Eyeglass wipes and coffee filters work well.
  5. Lightly moisten the swab or cloth and squeeze out the excess moisture.
  6. Holding the cartridge by its handle, wipe the copper contacts. Figure 4: Wiping the contacts c00372274.gif 1 - Copper contacts
  7. Replace the cartridge and then close the latch and the printer top cover.
  8. Check the printer for the error message. If the error message still displays, go to the next step.
    NOTE: The printer may take up to 15 seconds to clear the error and recognize the cartridge after closing the cover.
Step three: Replace the cartridge If the error message still displays, replace the indicated cartridge with a new cartridge.
Or Please let me know what is the exact error message you are getting.

Mar 21, 2009 | HP Photosmart C5180 All-In-One InkJet...

1 Answer

Dell printer model# A940 50c error


Test your cartridges.

Remove the color ink cartridge then lower the cover of your printer. If the error message displays again, replace the black cartridge with a new one (or return the new one). Reinstall the color cartridge and remove the black ink cartridge then lower the cover. If the error message displays again, replace the color cartridge with a new color cartridge.
Note: My manual indicated that the printer might have detected a short circuit in a cartridge. I returned a month old black cartridge got a new one and my printer is working fine now. Good luck.

Nov 10, 2008 | Dell A940 All-In-One InkJet Printer

2 Answers

Hp psc2410xi


The following error message appears on the color graphics display after you insert a cartridge: Remove and Check Print Cartridges . The printer will not print. The message does not specify which cartridge has caused the error. Solution This error message indicates that the printer cannot determine which cartridge is causing the error. Follow the steps below to solve the problem.
  1. Remove the color cartridge from the left stall (which has a blue latch) and refasten the latch. Leave the other cartridge in place.
  2. Close the printer, wait 10 to 15 seconds, then look at the LCD display.
    • If the LCD display reads Insert Color Cartridge in Left Stall , the color cartridge may be causing the problem. Follow the steps below:
      1. Clean the color cartridge contacts.
      2. Reinsert the color cartridge into the carriage and close the blue latch.
      3. Close the printer and wait 10 to 15 seconds.
      4. If the LCD display reads Remove and Check Print Cartridges , replace the color cartridge.
    OR
    • If the LCD display reads Remove and Check Print Cartridges , follow the steps below:
      1. Reinsert the color cartridge.
      2. Remove the black or photo cartridge, depending on which one is installed in the right stall. The right stall has the gray latch. Be sure to refasten the latch on the empty stall.
      3. Clean the black or photo cartridge contacts.
      4. Reinsert the black or photo cartridge.
      5. Close the printer and wait 10 to 15 seconds.
      6. If the LCD display reads Remove and Check Print Cartridges , replace the black or photo cartridge.

  1. Remove and then reinsert the cartridge indicated in the error message.
  2. If the error is still displayed, clean the contacts.
    1. If the error message is Error. Remove and Check Black or Photo Cartridge , the following steps may help:
    1. Remove both cartridges, lower the latches, and close the printer access door.
    2. Turn off the unit by pressing the On button on the front panel. Wait for the printer to completely shut down.
    3. Turn the printer back on by pressing the On button.
    4. When the message display reads Insert Print Cartridges , open the access door and replace the cartridges.
    1. If neither of the steps above fixed the problem, either the cartridge or the printer is faulty

    Aug 12, 2008 | HP LaserJet 5L Printer

    Not finding what you are looking for?
    HP OfficeJet 6210 All-In-One InkJet Printer Logo

    968 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top HP Office Equipment & Supplies Experts

    mukhtar21 shaikh
    mukhtar21 shaikh

    Level 3 Expert

    2022 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    Les Dickinson
    Les Dickinson

    Level 3 Expert

    18425 Answers

    Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...