Question about GE (PSS26MSRSS) Side by Side Refrigerator

1 Answer

"DE" system light flashing

My "DE" light is flashing on the front panel. I have push "system check/reset" and it cycles through all the other functions but still the "DE" light flashes. What's going on?

Posted by on

  • Anonymous Mar 12, 2014

    getfx24ejb "de" system light flashing

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 373 Answers

The DE error comes up when the refrigerator has not detected a defrostcurrent within a certain amount of time. This is most often the resultof a burnt out defrost heater. The refrigerator will likelykeep working for a week or so until the frost builds up and blocks theair flow over the evaporator (the cooling coils behind the back wall ofthe freezer). The defrost heater is located at the bottom of saidevaporator.
You can try your zip code in http://www.geappliances.com/buy/ and look for a servicing dealer.

Good luck.Please rate my answer if accepted.Thank you.

Posted on Jan 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the reset button on a mitsubishi dlp 73' tv?


  • Open the front panel by pushing on it. Pressing on the panel releases the lock and allows the front panel to pop open slightly. Pull the corner gently to open the panel completely.

  • 2

    Use a pointed object, such as the sharpened end of a pencil or the tip of a paper clip, to push the "System Reset" button.

  • 3

    Wait about one minute, or until the green LED light on the front panel display stops flashing.

  • 4

    Turn your television back on once the green LED light turns off.

    this is procedure for most mitsubishi dlp.

Oct 15, 2013 | Televison & Video

1 Answer

What do you do to get the error codes?


try to reset the
  • 1
    Open the front panel by pushing on it. Pressing on the panel releases the lock and allows the front panel to pop open slightly. Pull the corner gently to open the panel completely.

  • 2
    Use a pointed object, such as the sharpened end of a pencil or the tip of a paper clip, to push the "System Reset" button.




  • 3
    Wait about one minute, or until the green LED light on the front panel display stops flashing.

  • 4
    Turn your television back on once the green LED light turns off.


God bless you

Jul 27, 2013 | Mitsubishi WS-55859 55" Rear Projection...

1 Answer

Need instruction book for Cuisinart Single Serve Brewing System Model # CUISS-700


Here are the instructions to de-scale your Cuisinart SS-700, taken directly from the unit's manual, available here (www.cuisinart.com/share/pdf/manuals/ss-700.pdf):

1. Empty the reservoir.

2. Disable the AUTO OFF and OFF TIME features.

3. Making sure there is no K-Cup in the brewing chamber, fill the reservoir with 60 oz. of undiluted white vinegar.

4. Place a large mug on the drip tray and run a Hot Water cycle. Select the 12 oz. brew size. Discard contents of mug.

5. Repeat the hot water process until ADD WATER is displayed on the control panel and the reservoir lights will flash.

6. Let the Brewer stand for at least four hours while still on.

7. Rinse the water reservoir thoroughly and fill with fresh water.

8. Run another Hot Water cycle. Discard contents of large mug.

9. Repeat hot water process until ADD WATER is displayed on the control panel and the reservoir lights will flash.

10. You may need to perform additional Hot Water cycles if you detect any residual vinegar taste.

Note: If DE-SCALE is still displayed on the control panel after completing the procedure, repeat the de-scaling procedure above.

If you found this solution helpful, please leave a positive rating!

Sep 17, 2012 | Cuisinart SS700 SINGLE SERVE BREWING...

1 Answer

Will not spin or agitate


Remove the front panel. Observe the motor flashes.
The motor blinks on and off all the time.
It blinks faster when running.
If a failure occurs you will get the following flashes:

1 flash bad motor
2 flashes slipping belt
3 flashes corrupted software bad motor
4 flashes failed mode shift circuit
5 flashes bad motor
6 flashes locked motor check for objects between tub
7 flashes bad lid switch.
8 flashes motor overheated too much soap
9 flashes brake resister is toast bad motor.

To Reset the Inverter Board: Push the timer knob in so the washer is idle. Unplug the machine for one minute. Plug back in and raise and lower the lid six times within 12 seconds.

After resetting the inverter board, put the machine in a spin cycle and see if it runs. If not, check for a green blinking light on the inverter board. It will flash failure codes. If no light is visible you have a blown fuse built into the neutral side of the harness on the white/red wire.

themobilian_2813.jpgthemobilian_31.pngIf you see a small bubble in this black heat seal and the motor light is not on then the fuse within is blown replacement part is WH49X10041
What else do I have? Oh yeah how about the SERVICE MANUAL

Aug 12, 2011 | GE Profile WPRE6100G Top Load Washer

1 Answer

Washer will not spin or ajatate. I need to remove the front panel to see what up?


Use downwards force to relieve tension on the spring clips holding that front panel on.themobilian_1904.jpg

Video how to:

Once yall have the front panel removed yall will notice the motor has a green blinking light on it.
The motor blinks on and off all the time It blinks faster when running. That is normalment mon ami.
If it ain't acting right it will display flashes:

1 flash bad motor
2 flashes slipping belt
3 flashes corrupted software bad motor
4 flashes failed mode shift circuit
5 flashes little green men (bad motor)
6 flashes locked motor check for objects between tub
7 flashes bad lidswitch.
8 flashes motor overheated too much soap
9 flashes brake resister is toast bad motor.

To Reset the Inverter Board: Push the timer knob in so the washer is idle. Unplug the machine for one minute. Plug back in and raise and lower the lid six times within 12 seconds.

After resetting the inverter board, put the machine in a spin cycle and see if it runs. If not, check for a green blinking light on the inverter board. It will flash failure codes according to the picture above. If no light you probably have a blown fuse built into the neutral side of the harness on the white/red wire.themobilian_26.pngthemobilian_27.png

Service manual and more HERE


themobilian_1905.jpg

Mar 16, 2011 | GE Profile WPRE6150KWT Colossal Capacity...

1 Answer

''clean'' light flashing (whirlpool Dishwasher GU2300XTLS1 model)


I had the same problem recently and a repair person came to my home to fix the dishwasher. He said he had to reset the control panel. He did this simply by making sure the soap dispenser door inside the washer was closed, then making sure the main dishwasher door was closed and locked. Then he quickly pushed the Heated Dry button and the Hight Temp wash button alternately. He said each button needed to be pushed twice within five seconds. After he did this all the lights on the control panel came on, then turned themselves off before the washer went in to a test cycle. This simple reset fixed the whole problem. Works great so far.

Mar 26, 2009 | Dishwashers

1 Answer

Dryer does not work


Dryer just beeps, lights work, panel lights change, dryer just wont start. before this dryer worked but kept beeping thru the whole cycle. now nothing but lights.

Mar 13, 2009 | Whirlpool GEX9868J Electric Dryer

1 Answer

Door locked light flashing when door is closed


push on the door where the lock is... it may not be fully locked.

Feb 22, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Kenmore He4t- pushed cancel to add at start of load, now nothing but flashing lights


The manufacturer recommends unplugging the washer for at least 30 minutes to reset the computer. Sometimes this is all that is required to "cure" momentary "glitches". If this does not fix your problem, please post back and let me know. Hope this helps you.

Sep 11, 2008 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
GE (PSS26MSRSS) Side by Side Refrigerator Logo

499 people viewed this question

Ask a Question

Usually answered in minutes!

Top Refrigerators Experts

KJ4QOB

Level 2 Expert

55 Answers

Da Doc

Level 3 Expert

965 Answers

Jim Akins

Level 2 Expert

82 Answers

Are you a Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...