Question about Pioneer AVH-P6400CD Car DVD Player

1 Answer

Need the wiring diagram for avh-p6400cd

I need to know what each wire is for on that model.

Posted by on

  • jlaurence690 Mar 29, 2011

    My AVH-P4950DVD when playing DVD or VCD audio is work sound but no video. What seem to be the problem.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 379 Answers

Owners manual


installers guide



i believe you will find what you need in the installers guide , and a manual just in case you need it .

J5

Posted on Jan 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Do you need to connect the yellow and red wires together if not used in a car on a pioneer DEH-X1950UB


Yellow - Connect to the constant 12 V supply terminal.
Red - Connect to terminal controlled by the ignition switch (12 V DC).

Jan 11, 2017 | Pioneer Car Audio & Video

2 Answers

Where can I find the memory wire for the radio


Car radios don't have a 'memory wire'. Memory is held in integrated circuit chips called EPROMS, (electronically programmable, read only modules).

Jan 08, 2017 | Car Audio & Video

1 Answer

So how do wire this set set up to a bridged amp any help would be appreciated


assuming that is a dvc dual 4 ohm speaker, and you have a 2 ohm bridged amp, you run a positive from each side of the speaker into the bridged positive of the power amp, and run a negative from each side of the speaker into the negative bridged terminal of the amp. if, indeed, you have 2 4 ohm voice coils, running them bridged in parallel wiring will bring the load to 2 ohms. if you have 4 voice coils, of 4 ohms apiece, you could run all 4 parallel into the amp, but that would bring the load down to 1 ohm, and you would have to make sure you8r amp can support 1 ohm operation.

Jan 07, 2017 | Car Audio & Video

1 Answer

I have a boss 400w riot 2-4 channels,how do i connect the high level wires? Because stereo doesn't have rca's


to use the high level leads, you have to isolate the wires going to each speaker (if using 4 channel mode) or isolate the wires going just to the rear if you are using 2 channel mode. you have to strip a small piece of the insulation off each speaker wire, and run it into the amps high level input harness. if you dont have the high level input harness, you can get a 2 channel high level to rca adapter for around $20. basically, you are tapping into the signal to the stock speakers to feed music to the amp. make sure you get all your positives and negatives correct. brighter wires are usually positive; however you may be faced with sa speaker which uses a grey wire, and another grey wire- the second with a black line. you will have to, again, turn to internet research to determine which is positive and negative, if the colors are not obvious.

Dec 30, 2016 | Boss Car Audio & Video

1 Answer

Where can I find the connections the go on the back of the stereo


Usually behind the stereo in the console. Either a square or rectangle in shape. You can obtain adapters for differing units that allows the use of the original wiring harness without rewiring. Just a simple plug and play option.

Jan 01, 2015 | Car Audio & Video

1 Answer

I need the power plug wire harness that u hook the speakers up


If you wish to get some details; check the site linked here. Viewing it in "Mosaic" or "Magazine" will make surf easy. Pull up older posts. Surf the site with patience. Do a search by type in the brand name of your device at its search box and press "Enter".

Electro help

Jun 17, 2014 | Car Audio & Video

1 Answer

Car radio not turning off when the car is turn off


This has to do with the way the radio is wired. It's best to go into a motor-mechanics or car-audio shop to have them wire it correctly

Jun 09, 2014 | Car Audio & Video

Not finding what you are looking for?
Pioneer AVH-P6400CD Car DVD Player Logo

Related Topics:

2,073 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Car Audio & Video Experts

Michael Kovalik III
Michael Kovalik III

Level 2 Expert

117 Answers

The Knight
The Knight

Level 3 Expert

69845 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Pioneer Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...