Question about Dayton E52 Utility Heater

1 Answer

No spark my 3e219b 150.000 will not lite no spark

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 181 Answers

Has the transformer fallen off the motor assy.there are two screws that hold the transformer on.some times they vibrate out and the transformer losses it's ground.if they are in and tight you need a new one.cost about $80.00 for new one

Posted on Feb 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where to buy need parts for 3E219B need new filters


Do you need air filters or fuel filters or both?

Jan 14, 2011 | Dayton E52 Utility Heater

1 Answer

Green house heater 150,000 btu, changed tanks and supplier, replaced plugged pilot light, new thermostat. Heater comes on but makes horrible howling noise when burners light, experienced a small explosion...


The first thing I would do is have gas pressure checked, check pressure on the outlet side of regulator. Your gas supplier should do this for you for free or for minimum charge. It sounds to me like you have high pressure problem. I hope this helps. Thanks

Nov 19, 2010 | Dayton (3E379) Heater

1 Answer

150,000 BTU propane Reddy Heater shuts off after ignition


Is there a frost line on your LP tank, if so you may need to replace the tank with a larger tank or refill your tank. This can happen if the tank your using is too low or too small (use 100 lb tank or greater). If there is no frost line it may be an issue with the thermocouple. The manufacturer offers a service manual and owner's manuals on there site. This should assist you... www.desatech.com Thank you

Jan 28, 2010 | Reddy HEATER RLP100 100,000-BTU PORTABLE...

2 Answers

Dayton kerosene heater 3E219B will not turn on


I have a Dayton Model # 3e219b 150,000 BTU potable heater and it runs fine with the top cover off.But if I put the cover on it will go out is less than a minute and trip the reset.

Jan 31, 2009 | Reddy Heater-170,000 BTU Kerosene Deluxe

1 Answer

Laars lite 2 Spark egnighter will not spark


turn power off first. I would disconnect igniter wire which will be a thick orange wire that comes off of ignition module if it is spark. once you have that the end will look like a spark plug wire take shield away from metal then hold orange wire in hand close but not touching metal turn power on and it will take a couple of minutes before it should start sparking. If you don't see a spark then it is most likely the ignition module. There should be a red light on ignition module that will blink to tell you what the failure is if is is a newer on. When you turn power on to laars light 2 the inducer motor should come on then a pressure switch should send 24volt to gas valve for pilot to lite.Can you smell gas at all when laars should be igniting. If you have any questions fell free to email me back

May 10, 2008 | Lite On Laars Lite 2 Heaters: 250,000BTU...

1 Answer

Dayton 150,000 btu that won't stay lit


see if there is a pressues switch on the heater one of the tubes could be blocked,

Feb 16, 2008 | Dayton 511 Utility Heater

2 Answers

Dayton mod#3e219b gas heater


who told you air pump is supposed to be 5 psi? at the desatech site in their PDF troubleshooting guide air supposed to be 3.0-3.5 psi.

Dec 26, 2007 | Dayton G73 Utility Heater

1 Answer

Dayton mod#3e219b gas heater


air compressor output should be 3.5 psi. to the fuel nozzle. the cowlings purpose is to channel the air-fan output through the rear vanes of the combustion chamber. if these openings are restricted then air can't get into the chamber. check to see that the fan blades aren't jammed against the cowling. if they won't spin then you won't get any air through the unit.

Dec 21, 2007 | Dayton E52 Utility Heater

Not finding what you are looking for?
Dayton E52 Utility Heater Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dayton Heating & Cooling Experts

paulcarew

Level 3 Expert

2047 Answers

Mack Baxter

Level 3 Expert

381 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Dayton Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...