Question about Hobart A200 Stand Mixer

2 Answers

A200-T Hobart Mixer 1st speed have no torque

I have a hobart A200-T mixer that has a problem with 1st speed.
The 1st speed have no torque. I can stop it with my hand. The 2nd and
3rd. gears works perfect. I take it all apart and check all gears and keys
and they all good. I also try to adjust the bolts on the top and bottom
of the center shaft and still no luck. Please help!!!

Posted by on

  • mark_heaton Jan 21, 2009

    Thank you for your solution, but still don't understand what you
    talking about spring pin that locks the motor shaft. Can you
    email me a drawing of where about the part you are talking about.
    My email is mark-heaton@rogers.com

    Thank you in advanced



×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Hi mark,im a hobart tech and repair these mixers often.Depending on the year of the mixer there are 2 types of gear configurations for 1st speed.On older units they have a dive key---newer units have a spray clutch.When you took it apart did the center shaft (not the one to the left or upper left) have a big gear with ball bearings in it (spray clutch)?If not then its an older unit with a dive key.You need to take the center shaft apart and you will see a little spring built into the shaft,if theres no spring the whole shaft needs to be replaced if its intact it needs to be lubed--I think the spring would be broke.Any?

Posted on Jan 21, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the spring pin that locks the motor shaft to the main drive gear in the gear box. You should be able to turn the motor from the back at the cooling fins and watch the shaft spin in the gear, that is if the pin is sheared. That is a common problem. if you plan on keeping this machine for a while, i recomend that you spend a little more on a quality spring pin,

mechanictony-
good luck.

Posted on Jan 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hobart mixer


hi Gassman, below you will be able to find a link on parts assembly for the mixer, you will have an idea on how to tear off the parts, get them cleaned and place them back, like a regular maintenance.

Hobart A200 Mixer Parts Assembly

More parts assembly for Hobart A200 Mixer

hope this helps.

fb3484b.jpg

Aug 19, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 mixer. 1st gear has no torque, I can stop it by hand. I found the key sheared on the low speed gear(flat gear, beveled gear part wasn't sheared). I replaced the key, & it sheared it again...


Ed, if you continue to do it yourself, the end result will be tossing good money out. Have a professional check the system and save the unit from permanent damage. Chipping parts of a gear off means a serious resistance force or action has occurred. One force is slowing down as the other is speeding up. Gear alignment can be moved off center, or a sudden application (sudden stop or start) can damage the least resistant parts. For example, when a hook turns within the mixing chamber and the resistance of the content is too great on the turning shaft and gears, which ever part is weakest will break. Complicated I guess.

Mar 01, 2014 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 mixer 1st speed doesn't work 2nd and 3rd work fine


Could be that a gear is missing (broken) on the shaft that works the 1st gear. Check out the schematic at

http://www.food-equipment.com/parts_Hobart_mixers.htm

It could be the gear HM2-748

Feb 22, 2010 | Hobart A200 Stand Mixer

1 Answer

Speed reduction of Hobart A200 mixer


Hi Don. If your mixer is hurling honey, you must be very popular in the ant world...Sorry!

The Hobart electric motor on your mixer was designed and engineered to operate on 115-120 volt current and is the most dependable, and capable commercial mixer out there Is it possible for you to use a commercial Imerssion Blender for the first part of your mixing operation. Once your honey thickens a bit perhaps the a200 wouldn't hurl honey. Another consideration would be to either try a different beater or modify the one you have by removing surface area from the beater. If you remove metal, be sure to do it in a balanced fashion to avoid unwanted vibration in the beater. If you're not up to removing metal, take it to a machine shop and they'll do it for you. It probably won't take long, or cost much, and they have the expertise and the equipment to do it properly. If you found this solution helpful, please rate it. Good luck! ricardok45.

Feb 02, 2009 | Hobart A200 Stand Mixer

1 Answer

The gear is slipping on my Hobart A200


In what speed is it slipping?You only use 1st speed for dough,right?Can you put it in gear and stop the hook from moving with your hand?Let me know.

Jan 13, 2009 | Hobart N50 Stand Mixer

1 Answer

Hobart mixer


Please be more specific of what part you need.Whats the problem with the mixer?Im a hobart tech and service these mixers often.

Feb 18, 2008 | Hobart A200 Stand Mixer

1 Answer

A200 problem


Check the planetary.this is the bottom part of the mixer where you attach the hook.
You will see two nuts; make sure their tight as the planetary may have moved down.
Also have a look below:
http://cgi.ebay.com/HOBART-A200-20-QUART-MIXER-SERVICE-PARTS-MANUAL_W0QQitemZ160203114233QQcmdZViewItem

Feb 04, 2008 | Hobart A200 Stand Mixer

1 Answer

Hobart A200


amy, depending on how old your mixer is there are 2 types of clutches for 1st gear.these could be your problems--a key is sheared on the shaft--shaft/gear is broken.the bottom part of the mixer where you put on the attachements is called the planetary,does it look like it has moved down?you could tell if the dough hook,wire whip,ect,ect is hitting the bottom of the bowl.if this is the case its just simply tightening the 2 nuts next to the beater shaft.if this is not the case you would have to dissasemble the transmission.let me know.

Jan 11, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart A200 Stand Mixer Logo

460 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1138 Answers

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Shira

Level 2 Expert

119 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...