Question about Asko W620

2 Answers

Asko 620 moter failure?bearing replacement?

I took out the motor to see why it stopped working,I freed up the motor and got it to spin but I believe the bearings are going bad.It is making some high pitch whining noises.
Can I replace these bearings? or do I have to buy new motor?The motor looks like it doesnt come apart to easy..
Thanks

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Asko Master
  • 3,463 Answers

It is not normally possible to replace motor bearings, as they are pressed onto the shaft at the time of manufacture, making it virtually impossible to replace them.
I'm afraid it means a new motor.
Plz rate my solution.
Thanks.

Posted on Jan 18, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have same problem.
Front bearing has failed.
Front of motor will come off once I remove the drive pulley.
Pulley is held by staking the end of the motor shaft.
Part way through drilling out the staking, will finish tomorrow with help from my son. (cut left hand with an angle grinder and doc says no workshop work until fully healed!)
May need to make a puller to pull the drive pulley off, then undo the 4 long bolts with flat heads that hold the front housing.
Once off push out bearing in press and off to bearing service.
Bearings are only shielded, not sealed, so I guess have lost grease.Will use high quality sealed bearings, usually a 6200 series and readily available.
my email is rory_thompson@hotmail.com
If you want to follow up, send me an Email.
Rory Thompson MIEAust. CPEng. (2180308)

Posted on Feb 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 35mm circulersaw model p6455 450watt black & decker seems to be overheating & the blade doesent spin properly? how do i fix this whats the problem?


I can't find any references to a B&D saw with model number P6455 but it sounds like you have one or two bad armature bearings or bushings if so equipped. If they are bad it will make a lot of noise at startup and the motor will get hot and stop working because it's working harder than it should and building up excess heat. It may be possible to replace the bearings if the armature and field weren't overheated too badly. You'll have to search the web for your make with the proper model numbe to find if parts are available and if it's worth fixing.

Dec 25, 2011 | Black & Decker Saws

1 Answer

ASKO 7000 series washer drum stopped rotating. Smelled of burning. Could not turn the drum by hand. Guessing a burned out bearing as electronics and pump still work and are trying to turn steel drum. ...


check inside your washer for nails or other objects . I already seen a nail fall down in one of the basket holes and the nail stuck into the outer tub not allowing the basket to spin. If you dont see anything in the basket holes, then it is your bearings. The burning smell is coming from your belt. The motor is spinning but your basket is not. It is cheaper to buy a new washer. In ordered to fix your washer you have to rebuild it. The bearing are built into the outer tub of the washer.

Jul 13, 2011 | Asko 8005 Front Load Washing Machine

2 Answers

ASko dryer T761 goes bump bump bump when starting. sometimes we can wiggle drum around and get it to stop. Help!


I believe asko says this is normal at start up and should stop after the drum has been spinning for a bit.

Jun 21, 2011 | Asko T761 Electric Dryer

1 Answer

Motor/Drum doesn't turn/spin & belt appears to be OK


With the belt off can you spin the motor freely by hand? If no then the bearings are froze and the motor has to be replaced. If yes and the motor will not start when power is applied then the motor needs to be replaced. If it starts without the belt on but not with, then the drum is bound somewhere and has to be freed.
Eric

Jun 11, 2010 | Kenmore Dryers

1 Answer

Amana dlw330 washer belt urned & broke again


Had the same problem on a machine I worked on. Changed the belt... was burnt and broken. Second time I replaced the belt, I ran it through all of the cycles and listened to it on SPIN cycle.. Although it's spinning.. it's making an extremely LOUD noise... It's the Spin bearing that is gone out. When a load is put in, and in spin cycle, the bearing is oveloaded..(being dry).. and putting extreme pressure on the motor and belt. When the drum reaches a point where the bearing just won't spin, the belt stops, and spins on the motor pulley, wearing it through.. (And smoking a great deal).. until it breaks.. again. I believe the top "Spin bearing" is about 75.00 or so.. and a BEAR to replace. Hope this helps

Feb 26, 2009 | Amana DLW330RA Top Load Washer

2 Answers

Asko Dryer model T-701


you need to replace the motor you can replace the rear half of the motor but you can only buy a complete motor.this isnt a common problem but i have had it before.it broke because you need to grease the pin every 5 years or so.

Oct 24, 2008 | Asko T711 Electric Dryer

1 Answer

Asko 620 not spinning and not agitating


Clean armature and replace brushes. When you remove the brushes the shut a small pin like device maybe protruding from the brush tip. this is a sure clue.

Jun 18, 2008 | Asko W620

2 Answers

Broken AC window unit Kenmore


starting capacitor is bad (THE STARTING CAPACITOR IS A BIG METAL BLOCK MOUNTED ON OR NEAR FAN MOTOR)

Jan 17, 2008 | Heating & Cooling

3 Answers

Asko W620 washing machine not spinning


Sounds like the motor brushes need to be cleaned or replaced. Take the back off the washer, remove the motor and gently scrape the excess carbon or debris off the brushes with a pocket knife. I did this and it ran well for about 50 loads before building back up. I am ordering new brushes now because when I checked the brushes last week they were obviously worn more than 4 weeks ago.

Dec 11, 2007 | Asko W620

Not finding what you are looking for?
Washing Machines Logo

488 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

shaun taylor

Level 3 Expert

1497 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...