Question about Zanussi 18 in. DE4744 Free-standing Dishwasher

1 Answer

Is my zanussi aquapulse de 4744 dw hot or cold water fed ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 979 Answers

It is more than likely hot water fed. You can trace the line probably to under your kitchen sink and see where the line follows up to your hot/cold on your sink. There would be then another line coming off the hot which would lead to your dishwasher.

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washes but water does not heat up and dishes cold


The dishwasher does not heat up the water. The water should be hot coming into the dishwasher, check your hot water supply source, whether it be the hot water tank or be sure the water inlet for the dishwasher is not connected to the cold water line

Jan 09, 2011 | Zanussi Dishwashers

1 Answer

Zanussi Aquapulse DE6854 dishwahser programe lights not working


hi
got same probleme with my aquapulse 4744 slimline

Oct 07, 2009 | Electrolux Dishwashers

2 Answers

The Zanussi Aquapulse (de 6965) Fault Code AL3.


i have this now- another site suggested its the heater, or rater the circuit board. I have just taken it apart and have two dry solder points that are identified quire easily by soot around the area. so now off to find my soldering iron!!

Sep 26, 2009 | Zanussi 24 in. DE6965 Built-in Dishwasher

1 Answer

The first cycle water is not hot - all other cycles are hot - the water in the sink next to the dishwasher is not???


Where does the dishwasher connect to hot water? If it is connected to cold it must be changed. From your description, the water is coming from a long way off and has to warm the pipes as it travels to the dw. The dw should have a heater to bring the water up to temp after filling before it runs, if this heater is not working, the first run will be cold and the next hot because you have drawn enough water through the pipes to bring hot water to the dw.
1. Change where the dw gets hw.
2. Run hw in the sink before allowing the dw to start (if connected to same line).
3. Fix the dw's water heater.

Three possible fixes. Good luck.

Aug 27, 2009 | Maytag 24 in. DWU7402 Built-in Dishwasher

1 Answer

Housekeeper put dish washing soap in - machine is full of bubbles. How do I clean it out without flooding the kitchen?


Turn off the hot water supply to the DW. Take a pot or pan. Fill the DW tub with COLD water, pump it out. Repeat this COLD water and pump out several times until the suds are gone. HOT water only makes the suds worse and prevents the pump from expelling the water.

Jul 07, 2009 | Bosch Dishwashers

1 Answer

I have a Zanussi Fitted dishwasher and I notice that the board under my kitchen seems to be getting black,I think it is the dishwasher leaking water from underneath.. Is there any common problems with this...


Yes sounds like some kind of water leak. Take of the front plinth and check underneath the units and DW. I presume you DW is adjacent to the sink so please cheak all pipes including waste asap. Also opening the DW door whilst it is running can splash water, over a period of time this could effect wood material and cause your problem.

Mar 09, 2009 | Zanussi ZT485 Built-in Dishwasher

1 Answer

Hi there I have a Zanussi zdf121 dishwasher which is only doing a cold wash, not heating at all. Not sure if its hot fill but the hot water is fine elsewhere. Any ideas please Pete


Do you have it hooked up to hot or cold water supply? Most residential dishwashers don't come equipped with a booster heater. If it's connected to the cold side, you'll have to replace the angle stop with a single outlet stop and replace the hot angle stop with a double outlet stop. This should help out, if not, make sure you have hot water in the faucet before starting the dishwasher. Most dishwashers need at least 120 degree hot water supply.

Mar 02, 2009 | Zanussi 18 in. DA4342 Free-standing...

1 Answer

Need portable DW but have low hot water pressure in apartment


all dishwashers i am aware off have their own heater and are better connected to cold not hot water

Jun 26, 2008 | Dishwashers

1 Answer

Zanussi DE 6554 Dishwasher


Wash the dishes by hand and view them again 1 hour later. If the dishes are still cloudy it's too late you have been running in hard water for years and etched the dishes. Salt only regenerates the Xeolite beads inside the DW. They collect minerals until they can no longer hold more, then the DW washes the minerals off the beads with the salt. Check if the DW is set correctly to the appropriate water hardness of your town. READ THE OWNERS MANUAL. PS> 1. You can't use regular salt. 2. Is the salt dry? Salt must be added into water so it creates solution (brine).

May 05, 2008 | Dishwashers

2 Answers

Zanussi Aquapulse DE6544 not emptying


Zanussi Aquapulse dishwasher - is filled with water inside, is not washing and the lights keep flashing on and off - has anyone any idea what may be wrong with it?

May 27, 2007 | Zanussi 24 in. DE6544 Built-in Dishwasher

Not finding what you are looking for?
Zanussi 18 in. DE4744 Free-standing Dishwasher Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

paulcarew

Level 3 Expert

1914 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...