I have a Magnavox 2205 Combination DVD/DVR and I would like to change the the output channel from 3 to 4. I lost power at my house and the unit defaulted back to output channel 3. This unit, though inexpensive, has been working daily for my kids for years now, and I would like to keep it. I have misplaced my user's guide and there is no slide switch on the back as there used to be. It is older now, and I can't seem to find the user's guide online.
1: set tv to channel you want your vcr output to be on. 2: turn vcr on (if it is a vcr/dvd combo make sure it is on vcr) 3: put in video tape. 4: press play button one time, release it, and then press and hold it for three to five seconds. i had to call customer support to figure this out on mine.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
1) Set your TV to channel 3. 2) Insert a pre-recorded tape into this unit. 3) Press the OUTPUT button on the DVD/VCR so that the VCR OUTPUT light is lit. • If noise appears on the TV screen, press the VCR/TV button on the remote control. 4) Press the PLAY button once. 5) After a few seconds, press the PLAY button on the DVD/VCR for 3 seconds. • The RF output channel will change to channel 3 from channel 4 and you will see a playback picture. • When a picture does not appear on the TV screen, repeat step . 6) Press the STOP button to stop playback.
Don't hook the DVD/VCR recorder through ur cable box.Hook the DVD/VCR recorder through ur tv only it should work find.This way each units have it own direct functions to the tv.U recording the shows from the tv not the cable box ok.
ok i downloaded and read your DVR-1000 manual , this is what you will do .
While the DVD+VCR is turned off, press and hold CHANNEL (up/down) button on the front panel for about five seconds.
The unit will turn itself on and “RF 03” or “RF 04” appears on the front panel display
Use CH ( up / down ) button on the front panel or CH ( up / down ) button on the remote control to change the RF output channel (CH 03 or CH 04).
Turn the DVD+VCR off and then on
Set the TV to channel 3 or 4 depending on the RF output channel you selected. Now you can watch the DVD+VCR playback on CH3 or CH4 of your TV
PS , you should see a child lock button on the remote , if you press that button , you will disable front panel button controls so kids can't change anything , press it again to unlock that feature , it might come in handy.
THE CABLE OR ANTENA NEED TO SCREW INTO THE INPUT OF YOUR UNIT THEN A SMALL WIRE OUT TO THE TV FROM YOUR UNIT PUSH RECORD WHEN SHOW IS ON TV !SO ITS CABLE INTO VCR INPUT THEN CABLE FROM OUTPUT OF VCR TO TV ....TV ON CHANNEL 3 AND VCR UNIT ON CHANNEL 3
Unfortunately, Broksonic's website doesn't offer manual downloads. But product information for the 810C and 810D both say the output is channel 3/4 switchable. So if there isn't a rear panel switch (or one hiding somewhere else on the unit), it must be through a setup menu via the remote control. If you have the remote it shouldn't be too much trouble to experiment with the options until you find the right menu. If you didn't get the remote along with the unit, you are probably going to have to live with whatever channel it's on already.
You can watch the TV programs with the tuner of the unit. (Usually channel 3 or 4 of the TV is available for the RF converter setting.) Be sure to connect the unit to a TV using the RF cable. 1 Select channel 3 on your TV. 2 Press [VIDEO/TV] on the remote control. • If noise appears, change the RF output channel of the unit to CH 4 by pressing [VIDEO/TV] for 3 seconds. The RF output channel will alternate between CH3 and CH4