Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Washer spinning irregular.

Hello, My name is Betty, I have a whirlpool mod. gsq9669lwo when it's spinning the basket tilts forward and hits the front of the washer.I would like to know what would cause this.Thank you. :)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Your counter balance spring has broken off..onthjob

Posted on Jan 17, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kenmore he21 washer fill agitates drains but will not spin


My name is Peter. I am a retired field service technician.

The model number you gave HE21 comes up as a Maytag hot water tank.
Open the front door of you unit. The model number should be at the top on a tag.
Repost your question with this model number.

Nov 10, 2014 | Washing Machines

1 Answer

Have a Whirlpool Cabrio H.E. top load washer. probably 3 years old at the most. Recently making loud noises (bearings??) while in the spin cycles

Hello Byron. My name is Ashley and I am a representative of Whirlpool. We sincerely apologize for the frustrations you have experienced with your washer. We would like to look into this matter further on your behalf. Please email us directly at with your name, phone number, address, and the complete model and serial number for your washer. Please also include this reference number: 64337. Best regards, Ashley

Oct 27, 2013 | Whirlpool Washing Machines

1 Answer

How to change seal on frontload washer

Hello Betty Lamey - Replacing the gasket is a difficult task and I recommend consulting a service provider to move forward accurately. Usually this type of data is not release to a consumer and it is very rare to find enough information to do it yourself. In most cases some source can be found on the internet; however it is not provided directly from the manufacturer due to liability reasons.

Feb 16, 2013 | Electrolux EW1000i Front Load Washer

1 Answer

Water shooting from top

Hello Betty Lamey - That is an interesting location. The location from where the unit is leaking is not a common failure/complaint. The washer could possibly have a poor door gasket or damage/crack door. Contact a professional to move forward accurately.

Feb 16, 2013 | Electrolux EW1000i Front Load Washer

1 Answer

Wfmc3200uc101 bosch washer doesnot spin out when a single sweater is in. the drum turns but not at full speed

i have the same problem, what i find helps put a bed sheet in with the sweater to even the load, ( I keep a sheet by the washer for this specifically) and take it off max. spin cycle for the small load (I know this sounds stupid) I have a bosch also and I have problems with small blankets too. This usually helps, but I found that if i do this under the 25 minute quick wash instead of the regular wash it doesn't spin out either, kind of stupid to run a machine with only one sweater for 58 minutes, I would never buy a front loader again, betty

Jan 21, 2011 | Bosch WFMC 3200 Front Load Washer

1 Answer

Spin cycle does not work. Machine only hums when it should spin.

Check the motor capacitors. Wash cycle and run cycle capacitors are different in some m/cs.If these are OK motor winding to be checked.

Now it is ten years old and you are likely to get ball bearing problem. Get an repair estimate and decide which suits your budget.

Apr 06, 2010 | GE WBSE3120B Top Load Washer

1 Answer

Whirlpool Wash Machine and Agitator

check the direct drive coupling between the motor and the transmission

Apr 21, 2008 | Washing Machines

1 Answer

Maytag Neptune MAH400AWW

rear tub bearing is going out, must be replaced, causing too much drag. labor intensive repair.

Mar 26, 2008 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Roper Washer spinning cycle problem

This happened on mine as well. I determined that the clutch was bad. These are not belt driven but rather direct drive with a clutch/brake that controls the spins and agitate functions. Try washing an empty or very small load (like tshirts and underclothes) and see if that helps. ALso look underneath to see if there is any oil on the ground if so you most likley will need to replacet he cltuch mechanism... not an easy task for do it yourselfer!

Apr 05, 2007 | Roper RAS8445KQ Top Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides