Question about Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Kenmore HE3 washer emits steady, constant beeeeeeeeeeeeeep

The signal that normally beeps for end of cycle emits steady, constant and loud tone during entire wash, rinse and spin cycles. No error codes shown. Cycles seem to run fine. Diagnostic test shows no problems.

Posted by on

  • tripdip Jan 17, 2009

    forgot to note - I unplugged the washer for 15 minutes, but tone came right back upon restart.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 68 Answers

Depending on how your washer controls the beeper, it could be a stuck relay or a fried transistor.

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dryer beeps running


Hello Biff

You should the the following.

Level the dryer
Check the drum belt
Check the drum support rollers
Check the idler pulley
Check the glides
Check drum bearings
Check the blower
Check the baffles

Best Regards
Neciforo Llanto

Sep 21, 2013 | Kenmore Dryers

1 Answer

Kenmore elite he3 washer F02 error during wash cycle


You need to check for a blockage, F02 code indicates -- Drain blocked, kinked, drain filter plugged, or drain pipe exits too far above the washer.

Dec 22, 2012 | Kenmore HE3 Steam 7.2 cu. ft. Super...

1 Answer

My Kenmore Elite HE3 Mod 11044832 202 started making LOUD knocking noises during final spin cycle, then started to smell like something burning. Whit placis shreds in the washer.


the plastic is the drum has dropped so its eating a way the plastic on the back of the drum so no not worth fixing the mould is an easy fix just soke a cloth with neat bleach and leave over night make sure you do a rines after woulds as you don't want bleach on your cloths ok

Oct 21, 2012 | Kenmore 44832 Front Load Washer

1 Answer

Kenmore dryer beeps constantly


End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
@ H_GH
@ LOW
@ OFF
END of CYCLE S_GNAL
Press END of CYCLE SIGNAL to adjust the sound level or turn off
the signal.
NOTE: When WRINKLE GUARD _ is selected and the End of
Cycle Signal is on, a tone sounds every 5 minutes until the
clothes are removed, or WRINKLE GUARD _ ends.

Sep 15, 2009 | Dryers

1 Answer

Loud racket when spinning at high rate f speed


yes it is going. if you go here

www.techray1.com and select the guru guy he will take you another window where you can select the part needed. also the repair manual is availble for your unit.

Jun 22, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Help! Mt Kenmore Elite Quietpak2 HE3 keeps


F/06 Drive Motor Tachometer Error
The control is unable to properly detect motor speed and the machine will shut down. If a failure occurs during high-speed spin, the door will be unlocked after 3 minutes.
  • Check wire harness connections between the Drive Motor/Tachometer and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU)
  • Check the Drive Motor
  • Check the MCU
  • Check the Wire Harness

Mar 10, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

Cycle Signal Volume beeps from loud to soft


This is a common and very well known problem with the Oasis. You will need to replace the operator interface board inside the control panel to resolve this issue. The board is located directly behind the control knob. If you post back with your model number, I can research a part number for you, give you info on where you can order a replacement, and give you guidance on how to replace the board yourself.

Feb 12, 2009 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

3 quick beeps during cycle if you can get it to stay in a cycle


MY KENMORE OASIS HE IS DRIVING ME CRAZY! THE CYCLE SIGNAL CONTINUES TO BEEP AT LEAST 25 TIMES, STOPS FOR MAYBE 20 SECONDS, THEN BEEPS AGAIN ABOUT 25 TIMES. THE WASHER WORKS GREAT, BUT IT WILL NOT STOP BEEPING! HELP!!!!!

Sep 13, 2008 | Kenmore Oasis HE 27062 Top Load Washer

1 Answer

Loud/Soft signal


all i can figure is it is a strange method by kenmore to alert the user to throw in an antistatic cloth that gives softer clothes (clothes softener sheets)

May 25, 2007 | Kenmore 67052 Dryer

Not finding what you are looking for?
Kenmore 3.8 cu. ft. HE3 Front Load Washer Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Fordexpert

Level 3 Expert

5363 Answers

Archaeology
Archaeology

Level 3 Expert

662 Answers

reliableservice

Level 2 Expert

287 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...