Question about E-Machines (308714) Motherboard

1 Answer

No power to emachines t6522

I replaced the motherboard of my emachines t6522. i got al the wires hooked up except three wires that go together, their coors are green/white, black/white and red/white. do you know the configuration that these go to. also i did get the fans to work but nothing else. i ordered a replacement power supply hoping that woud help solve the problem. any ideas?

Posted by on

  • Anonymous Mar 17, 2009

    i have same problem but no manual

  • Anonymous Mar 17, 2009

    model t2896 no power

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 827 Answers

Hi,
The final set of connections are the front panel leads that attach to the motherboard. This includes the LEDs for hard drive activity and power status, the case speaker, and most importantly, the power switch.
eg:
no power to emachines t6522 - 9499f5a.jpg
You should consult your motherboard manual to find out where to plug these in. The power one is obviously the most important.

Hope this helps

Chris (ziraffa)

Posted on Jan 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How To Remove Front Panel For t5048 Emachines Tower


The eMachines T5048 Desktop PC, uses the NexGen 2 computer case.
(Also uses an Intel D102GGC2 motherboard)

1) http://www.hypermicro.com/mmhypermicrocom/images/CSEC004.JPG

The front panel is the Front Bezel.
It is removed by grasping the right side of it, and pulling out, G-E-N-T-L-Y

There Power On switch wires, Power On LED wires, USB front panel wires, Card Reader wires, etc., are still attached.

http://downloads.emachines.com/userguides/DesktopPC_UserGuide_en.pdf

(Page 47 - Removing the Front Bezel )

{ Note*
Usually there are plastic tabs formed out of the Front Panel, and they snap into slots in the metal computer case frame.

Usually 3 per side. They are flat, and have a hooked end.
They are pressed to the outside, or inside of the case, to release the hooked end away from the side of the slot.

LOOK at the tab. Look at the hooked end. SEE which direction THAT flat tab should be eased over to, in order to bring the hooked end away from the side of the slotted hole.

When the hooked end is in the middle of the slotted hole, the flat tab can then be eased OUT of the slotted hole.

DO NOT assume all tabs go in the same direction }

[ The area of contact pins on the motherboard, that the wires from the Front Panel go to, (Except for the USB and Card Reader), is the Front Panel header.

This link shows you the Front Panel header pinout,

http://www.intel.com/support/motherboards/desktop/d102ggc2/sb/CS-022441.htm

Click on the blue file name -
Intel Desktop Board D102GGC2 Product Guide - English (PDF)

{It's a Motherboard User Manual }

For additional questions please post in a Comment.

Regards,
joecoolvette

Feb 03, 2012 | eMachines T5048 PC Desktop

1 Answer

I need to know where 3 wires go


The wires should be labeled HDD,POWER, and i think RESET or somthing, just look on the motherboard within cord reach and you should see all three labeled on the motherboard all grouped together.

Oct 26, 2009 | E-Machines eMachines Desktop PC

1 Answer

Motherboard installation


Just download manual and check configurations:
http://www.opendrivers.com/driver/265244/emachines-c6415-user-guide-free-download.html

May 16, 2009 | Computers & Internet

1 Answer

Emachine T3958


Hopefully eMachines are consistent with their wiring/layout design, that being the case this diagram for T2898 (by benz18724) should point you in the right direction...

01fed5d.jpg

Alternatively compare the abbreviated pin symbols on the header to the motherboard and match them up.

Jan 31, 2009 | Computers & Internet

2 Answers

Emachines t6522


I assume you are trying to connect the wires from the faceplate to the motherboard. Get a magnifying glass and see if the board is marked as to Power, Speaker, HDD LED, Reset, etc. Trace the wires to the faceplate and note what the function of each pair of wires is and attach to motherboard as necessary.

Jan 17, 2009 | E-Machines eMachines Desktop PC

1 Answer

Emachines t6522


Hi birm,
I can tell you that most likely the white wire is the ground wire. The others are positive. The two manual found on eMachine's site does not provide enough of detail.
In this manual see;
Replacing the front I/O Panel (Pages 168, 170 see number 5).
http://downloads.emachines.com/userguides/8511279_eM_NG3_chassis_HW_ref_en.pdf

The information is not specific enough, my guess is the front panel connections is the cable to the far right. (Looking at the picture).
You can try by looking at the picture & hooking the cable as shown.
The white colored wire seems to face to the right. Than try the power on button. If system does not come on, turn the connector 180 & reconnect. Try the power on button on the case.

Listed at the bottom of the link below you can either chat with a tech or call tech. (Main site for the T6522)
http://www.emachines.com/support/product_support.html?cat=Desktops&subcat=T%20Series&model=T6522

User guide T6522;
http://downloads.emachines.com/userguides/Desktop_UG_Nexgen2_3_en.pdf

Good luck birm!

I wish I could be more specific.
Mike


Jan 16, 2009 | E-Machines (308714) Motherboard

1 Answer

Motherboard wiring


Green/wht normally = Reset or Power LED
Red/wht normally = HDD LED
And is the third red/BLACK?
There should be a label on the black pin jumper at the end of each wire.
Does it say anything?

Jan 16, 2009 | E-Machines eMachines Desktop PC

1 Answer

Emachine W3400/ front panel connections


they have to be plugged in horizontally although it is possible to plug them in vertically because the pins are evenly spaced either way. they are color coded just not like you would expect for example one plug has a green wire and a white wire the green side goes to the green pin and the white side goes to a green pin with a white cross you have to look close because there are several green pins which is what threw me off do this with all three plugs

Apr 19, 2008 | AMD eMachines Desktop System w/ 17'' CRT...

1 Answer

Motherboard


I doubt you can replace it with the same on unless you bought another motherboard from emachine. You can buy a new motherboard just make sure it will accept your cpu and memory. Also make sure it will fit in the case and it has the same connections as your old motherboard ex. hard drive, printer ports, power supply....

Jan 16, 2008 | E-Machines T6522 PC Desktop

Not finding what you are looking for?
E-Machines (308714) Motherboard Logo

1,108 people viewed this question

Ask a Question

Usually answered in minutes!

Top E-Machines Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18344 Answers

Are you an E-Machines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...